Fuji Electric MONITOUCH X1 Series Hardware Specifications page 6

In this manual, you will find various notes categorized under the following levels with the signal words "DANGER" and "CAUTION".
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and could
CAUTION
cause property damage.
Note that there is a possibility that items listed with
• Never use the output signal of the X1 series for operations that may threaten human life or damage the system, such as signals
used in case of emergency. Design the system so that it can cope with a touch switch malfunction. A touch switch malfunction may
result in machine accidents or damage.
• Turn off the power supply when you set up the unit, connect new cables, or perform maintenance or inspections. Otherwise,
electrical shock or damage may occur.
• Never touch any terminals while the power is on. Otherwise, electrical shock may occur.
• The liquid crystal in the LCD panel is a hazardous substance. If the LCD panel is damaged, do not ingest the leaked liquid crystal. If
leaked liquid crystal makes contact with skin or clothing, wash it away with soap and water.
• Never disassemble, recharge, deform by pressure, short-circuit, reverse the polarity of the lithium battery, nor dispose of the lithium
battery in fire. Failure to follow these conditions will lead to explosion or ignition.
• Never use a lithium battery that is deformed, leaking, or shows any other signs of abnormality. Failure to follow these conditions will
lead to explosion or ignition.
• Switches on the screen are operable even when the screen has become dark due to a faulty backlight or when the backlight has
reached the end of its service life. If the screen is dark and hard to see, do not touch the screen. Otherwise, a malfunction may occur
resulting in machine accidents or damage.
• Tighten the mounting screw on the fixtures of the X1 series to an equal torque of 7.08 Ibf-in (0.8 N·m).
Excessive tightening may cause deformation, breakage, or malfunction of the touch switch, which may result in damage to the
machine or an accident. Loose mounting screws may cause the unit to fall down, malfunction, or short-circuit.
• Check the appearance of the unit when it is unpacked. Do not use the unit if any damage or deformation is found. Failure to do so
may lead to fire, damage, or malfunction.
• For use in a facility or as part of a system related to nuclear energy, aerospace, medical, traffic equipment, or mobile installations,
consult your local sales representative.
• Operate (or store) the X1 series under the conditions indicated in this manual and related manuals. Failure to do so could cause fire,
malfunction, physical damage, or deterioration.
• Observe the following environmental restrictions on use and storage of the unit. Otherwise, fire or damage to the unit may result.
- Avoid locations where there is a possibility that water, corrosive gas, flammable gas, solvents, grinding fluids, or cutting oil can
come into contact with the unit.
- Avoid high temperatures, high humidity, and outside weather conditions, such as wind, rain, or direct sunlight.
- Avoid locations where excessive dust, salt, and metallic particles are present.
- Avoid installing the unit in a location where vibrations or physical shocks may be transmitted.
• Equipment must be correctly mounted so that the main terminal of the X1 series will not be touched inadvertently. Otherwise, an
accident or electric shock may occur.
• Check periodically that terminal screws on the power supply terminal block and fixtures are firmly tightened. Loosened screws or
nuts may result in fire or malfunction.
• Tighten the terminal screws on the power supply terminal block of the X1 series to an equal torque of 4.43 to 5.31 Ibf-in (0.5 to
0.6 N·m). Improper tightening of screws may result in fire, malfunction, or other serious trouble.
• The X1 series has a glass screen. Do not drop the unit or impart physical shocks to the unit. Otherwise, the screen may be damaged.
• Correctly connect cables to the terminals of the X1 series in accordance with the specified voltage and wattage. Overvoltage,
overwattage, or incorrect cable connection could cause fire, malfunction, or damage to the unit.
• Always ground the X1 series unit. The FG terminal must be used exclusively for the X1 series unit with the level of grounding
resistance being 100  or less. Failure to do so may result in electric shock, fire, prevent correct touch operations or cause
malfunctions.
• Prevent any conductive particles from entering into the X1 series unit. Failure to do so may lead to fire, damage, or malfunction.
• Do not attempt to repair, disassemble, or modify the X1 series unit yourself. Contact Hakko Electronics or the designated contractor
for repairs.
Notes on Safe Usage of MONITOUCH
CAUTION
may have serious ramifications.
DANGER
CAUTION