Table of Contents
Advertisement
• When alighting from or getting into the operator's com-
partment, always face the machine and use the steps
and access handles.
• Be sure you know the position and function of each
control. Incorrect operation of the controls can cause
serious injuries.
• Check all controls and safety devices in a safe, open
area before starting work.
• Keep away from dangerous areas such as ditches,
overhangs, rocky areas, etc. Make a survey of the
work-site and determine the possible dangers before
using the machine.
• Before parking the machine, make sure that the ground
is stable. Plan the worksite so that the ground is flat,
hard and level.
• Before moving the machine to work in a new area, walk
around to determine all possible causes of accidents
there. Holes, obstacles, debris and other danger risks
in the working area can cause serious injury.
• Be ready to meet emergencies. Always carry a first aid
kit and if possible, fire extinguisher (not supplied) within
easy reach on board. Make sure the fire extinguisher
is regularly serviced in conformance with the manufac-
turer's instructions.
• Check the fastening of the main components: counter-
weight, turntable bearing and operator's compartment.
In the event of problems, consult your CASE CON-
STRUCTION Dealer.
Operating the machine
• When working on a public highway, use standard traf-
fic signs and take into consideration the working range
of the upperstructure and its attachments. Local or na-
tional regulations stipulate the number, type and loca-
tion of reflector strips.
• Avoid running the engine in a confined space. If there
is no alternative, proper ventilation must be provided at
all times.
• Do not allow anyone else on the machine. The passen-
ger could fall or cause an accident.
• Never operate the working or travel controls unless you
are properly seated in the operator's seat with the seat
belt correctly fastened.
• Before starting the engine, check the direction of travel
(in forward drive, the reduction gears should be to the
rear of the machine).
• Do not work near overhead high-voltage electric lines
without checking beforehand that all necessary mea-
sures have been taken to respect the minimum dis-
tances:
Less than 57000 volts: 3 m (9.8 ft).
More than 57000 volts: 5 m (16.4 ft).
• Study the position of any existing pipelines or conduits
before starting work. Electrical cables, gas and water
2 - SAFETY INFORMATION
• Make sure you understand the symbols used on the
machine safety decals. Keep the decals clean so that
they are perfectly legible at all times.
• Work out a means of convenient escape from the ma-
chine (emergency exit via the windshield or the rear
window glass) in the event of the machine turning over
or tipping over or the cab door being jammed.
• Make sure you are perfectly familiar with traffic regu-
lations and special safety equipment requirements be-
fore transporting this machine on a public highway.
• When loading trucks, never swing the load over the
truck cab.
• Before undertaking any travel on the job site, make sure
the itinerary to be followed is completely safe. If bridges
are to be crossed, make sure they are perfectly capable
of supporting the weight of the machine.
• Always steer round large obstacles such as boulders,
big trees, etc.
Quick coupler (optional)
• Every day, check that the locking bar functions correctly
and that it is not fouled by foreign matter. Clean the
locking system if necessary.
• If you are obliged to use the quick coupler with buckets
not manufactured by CASE CONSTRUCTION, make
sure the diameter of the pins and the width between
the bucket lugs meet the dimensions needed to fit the
quick coupler (pins, washers, bushings, etc.). Consult
your CASE CONSTRUCTION Dealer.
pipes and other underground installations can cause
serious injury.
• Always make allowance for working conditions (sloping
or rough ground), the site and weather conditions when
driving the machine.
• Do not allow anyone to stand in the machine working
area. Accidental operation of the upperstructure swing
control or of an attachment control could cause an ac-
cident. Stop all operations until everyone has moved
away.
• Before operating the dozer blade (if equipped) make
sure that there is no one in the working area of the latter.
• Operate all controls gradually to ensure smooth ma-
chine operation.
• Whenever load handling operations are to be carried
out, it is imperative to adhere strictly to the instructions
given in this manual and local legislation.
• It is forbidden to use the machine to carry out tasks
other than those for which it is intended. Never use the
equipment for sweeping the ground to level out rubble
or push objects (transversal stress on the attachment).
• Stop the engine and remove the ignition key when the
machine is not in use, even for short periods of time.
2-7
Advertisement
Table of Contents
