Tightening Torques - Case CX130C Operator's Manual

Tightening torques

Check the tightening torques every 250 h (after the first 50 h during the run-in period).
NOTICE: At the end of each working day, check all mounting nuts and screws for tightness and tighten if necessary.
Make sure no hardware items are missing. Replace them, if necessary.
Component
Travel reduction gears (*1)
Drive sprocket (*1)
Idler wheel (*1)
Upper roller (*1)
Lower roller (*1)
Chain guide (*1)
Counterweight (*2)
Turntable (lower frame)
Turntable (swing frame)
Swing reduction gear (*1)
Engine (*1)
Engine mount (*1)
Radiator
Hydraulic pump (*1)
Hydraulic tank (*1)
Fuel tank (*)
Control valve
Center joint (*1) (lower frame)
Center joint (*1) (swing frame)
Cab
Battery
NOTE: On the screws with mark (*1), use L
NOTE: To the threads with mark (*2), use L
6 - MAINTENANCE
Screw Wrench
M16 24 mm
M16 24 mm
M16 24 mm
M16 24 mm
M16 24 mm
M16 24 mm
M27 41 mm
M16 24 mm
M16 24 mm
M16 24 mm
M12 19 mm
M16 24 mm
M12 19 mm
M10 17 mm
M20 Hexagon wrench 223 – 247 N·m (164.48 – 182.18 lb ft)
M16 24 mm
M16 24 mm
M16 24 mm
M12 19 mm
M12 19 mm
M16 24 mm
M10 17 mm
® 262™ or its equivalent.
OCTITE
® M
OCTITE OLY
6-36
Torque setting
267 – 312 N·m (196.93 – 230.12 lb ft)
267 – 312 N·m (196.93 – 230.12 lb ft)
267 – 312 N·m (196.93 – 230.12 lb ft)
267 – 312 N·m (196.93 – 230.12 lb ft)
267 – 312 N·m (196.93 – 230.12 lb ft)
267 – 312 N·m (196.93 – 230.12 lb ft)
1078 – 1274 N·m (795.09 – 939.65 lb ft)
280 – 312 N·m (206.52 – 230.12 lb ft)
280 – 312 N·m (206.52 – 230.12 lb ft)
280 – 312 N·m (206.52 – 230.12 lb ft)
109 – 127 N·m (80.39 – 93.67 lb ft)
265 – 314 N·m (195.45 – 231.59 lb ft)
63.8 – 73.6 N·m (47.06 – 54.28 lb ft)
63.7 – 72.60 N·m (46.98 – 53.55 lb ft)
232 – 276 N·m (171.11 – 203.57 lb ft)
232 – 276 N·m (171.11 – 203.57 lb ft)
267 – 312 N·m (196.93 – 230.12 lb ft)
88.30 – 107 N·m (65.13 – 78.92 lb ft)
109 – 127 N·m (80.39 – 93.67 lb ft)
149 – 173 N·m (109.90 – 127.60 lb ft)
19.60 – 29.40 N·m (14.46 – 21.68 lb ft)
D F L or its equivalent.
RY ILM UBRICANT