Subscribe to Our Youtube Channel
Related Manuals for Case CX130B
Summary of Contents for Case CX130B
- Page 1 SERVICE MANUAL CRAWLER EXCAVATOR CX130B TIER 3 84139197B NA Replaces 84139197A NA Issued 01May 08 Revised 01Nov 08...
- Page 2 CRAWLER EXCAVATOR CX130B SERVICE MANUAL TABLE OF CONTENTS DIVISION/SECTION SECTION N° REFERENCE N° GENERAL INFORMATION Safety, general information and standard torque data........1001 7-27691NA General specifications and special torque setting ........... 1002 SC130B1002-1NA ENGINE Removal and installation of the engine............2000...
- Page 3 DIVISION/SECTION SECTION N° REFERENCE N° UPPERSTRUCTURE HYDRAULICS Depressurising and decontaminating the hydraulic system, use of the vacuum pump and bleeding the components..........8000 SM160B8000-0NA Specifications, troubleshooting, checks and hydraulic pressure settings................8001 SC130B8001-0NA Removal and installation of the hydraulic reservoir .........8002 SM130B8002-0EN Removal and installation of the main hydraulic pump........8003 SM130B8003-0EN Removal and installation of the main hydraulic control valve......8004...
- Page 4 Section 1001 SAFETY, GENERAL INFORMATION AND TORQUE SPECIFICATIONS Copyright © 2006 CNH America LLC. All rights reverved. Printed in U.S.A. Issued February, 2006 Lep 7-27691NA...
- Page 5 Thanks very much for your reading, Want to get more information, Please click here, Then get the complete manual NOTE: If there is no response to click on the link above, please download the PDF document first, and then click on it. Have any questions please write to me: admin@servicemanualperfect.com...
- Page 6 1001-2 TABLE OF CONTENTS GENERAL INFORMATION ............................3 SAFETY..................................4 STANDARD TORQUE DATA FOR CAP SCREWS AND NUTS................6 WARNING : This symbol is used in this manual to indicate important safety messages. Whenever you see this symbol, carefully read the message that follows, as there is a risk of serious injury. Lep 7-27691NA Issued 02-06...
- Page 7 Parts Catalog for the correct part Bearings number of the genuine Case replacement items. Failures due to the use of other than genuine Case Check bearings for easy action. If bearings have a replacement parts are not covered by warranty.
- Page 8 Operator’s and Service Manuals may be obtained from WARNING: Read the operator’s manual to your Case dealer. familiarize yourself with the correct control functions. WARNING: If you wear clothing that is too...
- Page 9 1001-5 WARNING: When servicing or repairing the WARNING: Use insulated gloves or mittens machine, keep the shop floor and operator’s when working with hot parts. compartment and steps free of oil, water, grease, tools, etc. Use an oil absorbing material and/or shop cloths as required. Use WARNING: Lower all attachments to the safe practices at all times.
- Page 10 1001-6 STANDARD TORQUE DATA FOR CAP SCREWS AND NUTS Tightening of cap screws, nuts Tighten alternately so that tightening torque can be applied evenly. The numbers in the figure below indicate the order of tightening. JS00481A Cap screws which have had Loctite used (white residue remains after removal) should be cleaned with loght oil or suitable cleaning solvent and dried.
- Page 11 Section 1002 SPECIFICATIONS AND SPECIAL TORQUE SETTINGS Copyright @ 2008 CNH America LLC. All rights reserved. Printed in USA. Lep SC130B1002-1NA May 2008...
-
Page 12: Table Of Contents
1002-2 TABLE OF CONTENTS WARNING: This symbol is used in this manual to indicate important safety messages. Whenever you see this symbol, carefully read the message which follows. Your safety depends on it. TYPE, SERIAL NUMBER AND YEAR OF MANUFACTURE OF THE MACHINE..................... 4 Machine .................................. - Page 13 1002-3 DIMENSIONS AND WEAR LIMIT OF THE TRACK ASSEMBLY ...................25 Sprocket..................................25 Idler wheel ..................................26 Upper roller .................................27 Lower roller .................................28 Track...................................29 DIMENSIONS AND WEAR LIMITS OF ATTACHMENT MOBILE JOINTS ..............30 1. Boom foot/Frame ..............................30 2. Boom cylinder foot/Frame............................31 3. Boom cylinder head/Boom............................31 4.
-
Page 14: Type, Serial Number And Year Of Manufacture Of The Machine
For all part orders, request for information or assistance, always specify the type and the serial number of the machine to your Case dealer. Fill in the following lines with the required information: Type, serial number, year of manufacture of the machine and the serial numbers of the hydraulic and mechanical components. -
Page 15: Fluids And Lubricants
CASE/AKCELA: HYDRAULIC EXCAVATOR FLUID (MS 1230. ISO VG 46. DIN 51524 PART 2 HV) Hot climates: 0°C to +50°C (32° to 122° F) CASE/AKCELA: AW HYDRAULIC FLUID 68 HV (MS 1216. ISO VG 68. DIN 51524 PART 3 CATEGORY HVLP) Cold climates: -25°C to +20°C (-13° to 68° F) CASE/AKCELA: AW HYDRAULIC FLUID 32 (MS 1216. -
Page 16: Engine Oil
1002-6 Engine Oil THE CASE/AKCELA No. 1 engine oil is recommended for your engine. This oil ensures proper lubrication of your engine for all operating conditions. If the CASE/AKCELA Multigrade "No. 1 ENGINE OIL" cannot be obtained, use the oil corresponding to one of the following categories: ACEA E7 API CI-4. -
Page 17: Engine Fuel, Maintenance Of Fuel Filters And Fuel Storage
1002-7 Engine fuel, maintenance of fuel filters and fuel storage In order to meet the emission control regulation of 3rd-stage, the engine components have been made precisely and they are to be used under high-pressure conditions. Therefore, the specified fuel must be used for the engine. As a matter of course, not only the guarantee will not be given for the use of a fuel other than the specified but also it may invite a serious breakdown. - Page 18 In this case, do not use these fuels because damage to the engine may result as the fuel has been contaminated. It is natural that the emission control regulation of 3rd-stage will not be cleared in case where a fuel that does not meet the specifications and the requirements is used.
-
Page 19: Anti-Freeze/Anti-Corrosion
Never throw oil or fluid on the ground and never place it in leaking receptacles. Contact your local ecological recycling centre or your CASE Dealer to obtain information on the correct method of dis- posing of these lubricants. -
Page 20: Specifications
Maximum drawbar pull .........................115 kN (25853.03 lbf) Grade ability ............................... 70% (35°) Ground pressure CX130B......................34 kPa (600 mm (23.62 in) grouser shoe) CX130B (Blade) ....................41 kPa (600 mm (23.62 in) grouser shoe) Complete machine dimensions Arm (dipper) CX130B (Standard boom) -
Page 21: Main Body Dimensions
1002-11 Main body dimensions Main body width ......................See machine overall dimensions Upper side swing body width ......................... 2540 mm (100 in) Cab width ............................1000 mm (39.37 in) Main body height..........................2820 mm (111.02 in) Tail swing radius ..........................2130 mm (83.86 in) Swing body tail distance........................ -
Page 22: Capacity Of Coolant And Lubricants
1002-12 Capacity of coolant and lubricants Coolant ..............................14.6 L (3.86 gal) Fuel ................................260 L (68.7 gal) Lubricant for engine............................. 17 L (4.49 gal) Lubricant for travel reduction gear (per side)....................2.1 L (0.55 gal) Lubricant for swing reduction gear (per side) ..................... 2.2 L (0.58 gal) Hydraulic oil .............................
Need help?
Do you have a question about the CX130B and is the answer not in the manual?
Questions and answers