Canon SADDLE FINISHER K3 Service Manual page 9

1.2.3 Removing the Paddle Unit
........................................... 3-16
1.2.4 Removing the Handling Tray
........................................... 3-16
1.2.5 Removing the Alignment Motor
........................................... 3-17
1.3 Tray A Unit/Tray B Unit .......... 3-19
1.3.1 Moving Down the Tray A/B
Unit .................................... 3-19
1.3.2 Removing the Tray A Unit
........................................... 3-20
1.3.3 Removing the Tray B Unit
........................................... 3-20
1.3.4 Removing the Try A/B Lift
Motor (M13/M12) ............. 3-21
1.3.5 Mounting the Tray A/B Lift
Motor (M13/M12) ............. 3-22
1.3.6 Adjusting the Position of the
Sub Tray Solenoid (SL3; with
paper folding unit istalled) . 3-23
1.3.7 Position of Tray B at Power-On
........................................... 3-24
1.3.8 Harness of the Tray A/B .... 3-25
1.3.9 Points to Note When Handling
the Stack Wall Rail ............ 3-25
1.4 Knurled Belt Releasing Unit .... 3-26
1.4.1 Removing the Knurled Belt
Releasing Unit ................... 3-26
1.5 Knurled Belt ............................. 3-27
1.5.1 Remove the Knurled Belt .. 3-27
1.6 Buffer Roller Unit .................... 3-28
1.6.1 Removing the Buffer Roller
Unit .................................... 3-28
1.7 Stapler Unit .............................. 3-33
1.7.1 Removing the Stapler ........ 3-33
1.7.2 Adjusting the Position of the
Stapler Paper Stopper ........ 3-34
1.7.3 Positioning the Stapler ....... 3-35
1.7.4 Adjusting the Position of the
Stapler (front, 1-point) ....... 3-38
1.7.5 Adjusting the Stapling Position
(rear, 1-point) ..................... 3-39
1.8 Punch Unit ............................... 3-41
COPYRIGHT© 2001 CANON INC. 2000 2000 2000 2000 CANON SADDLE FINISHER K3/K4 REV.0 MAR. 2001
1.8.1 Removing the Punch Slide Unit
........................................... 3-41
1.8.2 Mounting the Punch Waste Case
Holder ................................ 3-44
1.9 PCBs ........................................ 3-45
1.9.1 Removing the Finisher
Controller PCB .................. 3-45
2 Saddle Stitcher Assembly ................. 3-46
2.1 Saddle Unit .............................. 3-46
2.1.1 Removing the Saddle Unit
........................................... 3-46
2.1.2 Removing and Mounting the
Folding Roller .................... 3-49
2.1.3 Adjusting the Position of the
stitcher ............................... 3-54
2.1.4 Mounting the Positioning Plate
Unit .................................... 3-58
2.1.5 Removing the No. 1/No. 2
Paper Deflecting Plate ....... 3-59
2.1.6 Fitting of the Saddle Unit .. 3-60
2.1.7 Removing/Mounting the Paper
Pushing Plate ..................... 3-62
3 Paper Folding Unit-B1 (folder) ........ 3-66
3.1 External Covers ........................ 3-66
3.2 Folder ....................................... 3-66
3.2.1 Disconnecting from the Copier
........................................... 3-66
3.2.2 Removing the Folder (upper)
........................................... 3-67
3.3 Feeding System ........................ 3-70
3.3.1 Positioning the Folding Stopper
........................................... 3-70
3.3.2 Adjusting the Inlet Guide .. 3-73
3.3.3 Adjusting the Pressure of the
Folding Roller .................... 3-74
3.3.4 Adjusting the No. 1 Folding
Path Guide Plate ................ 3-77
3.3.5 Adjusting the Position of the
Left Guide Static Eliminator
........................................... 3-77
3.4 Drive System ............................ 3-78
3.4.1 Removing the Folder Motor
(M71) ................................. 3-78
INTRODUCTION
vii