Canon SADDLE FINISHER K3 Service Manual page 10

INTRODUCTION
3.4.2 Positioning the Coupling for the
Horizontal Path Drive ........ 3-79
3.4.3 Adjusting the Tension of the
Feeding Belt ....................... 3-80
3.4.4 Adjusting the Position of the
Pressure Releasing Solenoid
(SL73) ................................ 3-81
3.4.5 Adjusting the Position of the
Pressure Solenoid (SL74) .. 3-82
3.5 Removing the Folder Driver PCB
................................................. 3-83
4 Inserter .............................................. 3-84
CHAPTER 4 MAINTENANCE AND INSPECTION
1 Periodically Replaced Parts ................ 4-1
1.1 Finisher Unit .............................. 4-1
1.2 Saddle Stitcher Unit ................... 4-1
1.3 Folder ......................................... 4-1
1.4 Inserter ....................................... 4-1
2 Guide to Durables ............................... 4-2
2.1 Finisher Unit .............................. 4-2
2.2 Saddle Stitcher Unit ................... 4-2
CHAPTER 5 TROUBLESHOOTING
1 Making Adjustments ........................... 5-1
1.1 Electrical System ....................... 5-1
1.1.1 Adjusting the Alignment Width
............................................. 5-1
1.1.2 Adjusting the Stapling Position
(front, 1-position) ................ 5-2
1.1.3 Adjusting the Stapling Position
(rear 1-point) ........................ 5-4
1.1.4 Adjusting the Wrapping on the
Buffer Roller ........................ 5-5
1.1.5 Sensor Initial Adjustment .... 5-7
1.1.6 Adjusting the Speed of the
Swing Guide ........................ 5-8
1.1.7 Indication for the Swing Guide
Speed ................................... 5-9
1.1.8 Adjusting the Position of Punch
Holes (feed direction) ........ 5-10
viii
COPYRIGHT© 2001 CANON INC.
4.1 Externals and Controls ............. 3-84
4.1.1
4.1.2
4.1.3
4.1.4
4.2 Pickup Unit .............................. 3-90
4.2.1
4.2.2
4.2.3
2.3 Folder ......................................... 4-2
2.4 Inserter ....................................... 4-3
3 Scheduled Maintenance ...................... 4-4
3.1 Finisher Unit .............................. 4-4
3.2 Inserter ....................................... 4-4
3.3 Maintenance Procedure .............. 4-5
3.3.1
1.1.9
1.1.10 Adjusting the Sensitivity of the
1.1.11 After Replacing the EEPROM
1.1.12 Replacing the Finisher
1.1.13 Initializing the RAM .......... 5-15
1.1.14 Selecting Upward Curl Paper
1.1.15 Selecting Downward Curl Paper
1.1.16 Adjusting the Folding Position
2000 2000 2000 2000 CANON SADDLE FINISHER K3/K4 REV.0 MAR. 2001
External Covers ................. 3-84
Removing the Inserter ....... 3-84
Fixing the Inserter .............. 3-86
Correcting the Skew .......... 3-88
Removing the Pickup Unit
........................................... 3-90
Removing the Pickup Roller
........................................... 3-97
Positioning the Side Guide .......
........................................... 3-97
Cleaning the Components
Inside the Inserter ................ 4-5
Adjusting the Punch Hole
Position (in direction of
horizontal registration) ...... 5-11
Sensors ............................... 5-12
(IC102) .............................. 5-14
Controller (in response to E505)
........................................... 5-15
Mode .................................. 5-16
Mode .................................. 5-17
(saddle stitcher assembly) .. 5-19