Advertisement
PREPARATION FOR USE
© Bostitch
PRE-START CHECKLIST
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
1. Ensure the On/Off switch (6) is in the OFF position.
compliance for the products.
2. Plug the power cord into the correct branch circuit
GB
receptacle. See Electrical Connection (above).
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne
3. Ensure air tank is drained, see Draining Air Tank under
signifient en rien que les produits soient conformes aux normes CE.
Maintenance.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments
4. Ensure the drain valve (2) is closed.
erfüllen nicht die CE-Richtlinien für Produkte.
5. Ensure safety valve (9) is functioning properly, see Checking
Safety Valve under Maintenance.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document
6. Turn regulator knob (4) anticlockwise until fully closed.
willen niet zeggen dat de producten voldoen aan de CE-vereisten.
Ensure regulated pressure gauge reads 0 bar (0 psi).
7. Attach hose and accessories.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse
for produkterne.
m WARNING: Risk of unsafe operation. Firmly grasp hose
in hand when installing or disconnecting to prevent hose
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille
whip.
CE-yhdenmukaisuutta.
8. Ensure all covers and labels are in place, legible (for labels)
and securely mounted. Do not use compressor until all items
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
have been verified.
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
m WARNING: Risk of bursting. Too much air pressure causes
a hazardous risk of bursting. Check the manufacturer's
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non
maximum pressure rating for air tools and accessories. The
garantiscono la conformità CE per i relativi prodotti.
regulator outlet pressure must never exceed the maximum
pressure rating.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke
kravene for CE-merking for produktet.
INITIAL SET-UP
m WARNING: Do not operate this unit until you read and
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão
understand this instruction manual for safety, operation and
em conformidade com a CE para os produtos.
maintenance instructions.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
BREAK-IN PROCEDURE
conformidad con las normas CE de los productos.
m WARNING: Risk of property damage. Serious damage may
result if the following break-in instructions are not closely
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
followed.
conformidad con las normas CE de los productos.
This procedure is required before the air compressor is put
into service for the first time and when the check valve or a
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego
compressor pump/motor has been replaced.
dokumentu nie stanowią deklaracji zgodności CE prezentowanych produktów.
1. Ensure the On/Off switch (6) is in the OFF position.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego
m CAUTION: If hose is not connected to Quick Connect body,
dokumentu nie stanowią deklaracji zgodności CE prezentowanych produktów.
pull coupler back until it clicks to prevent air from escaping
through the quick connect.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE
2. Plug the power cord into the correct branch circuit
pre dané výrobky.
receptacle. See Voltage and Circuit Protection under
Installation.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum
3. Open the drain valve (anticlockwise) fully to permit air to
nem jelenti a termék CE-megfelelőségét.
escape and prevent air pressure build up in the air tank
during the break-in period.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
4. Move the On/Off switch to the ON position. The compressor
conformitatea CE pentru produse.
will start.
5. Run the compressor for 20 minutes.
8
6. After 20 minutes, close the drain valve by turning clockwise.
The tank will fill to cut-out pressure and the motor will stop.
7. Compressed air will be available until it is used or bled off.
STARTING
Check that the mains power matches that indicated on the
electrical data-plate - the permissible tolerance range is +/-5%.
Turn or press into position "0". Fit the plug in the power socket
and start the compressor, moving the On/Off switch into
position "I".
The compressor is fully automatic, and is controlled by the
pressure switch which stops it when tank pressure reaches
maximum value and restarts it when it falls to minimum value.
The pressure difference between maximum and minimum
values is usually about 2.4 bar (35 psi). E.g.: the compressor
stops when it reaches approximately 13.8 bar (200 psi) -
maximum operating pressure) and restarts automatically when
the pressure inside the tank drops to 11.4 bar (165 psi).
After connecting the compressor to the power line, run it to
maximum pressure and check exactly how the machine is
operating.
m WARNING: The head/cylinder/delivery tube unit can reach
high temperatures. Take care when working near these parts,
and do not touch them to avoid possible burns.
IMPORTANT
The electro-compressors must be connected to a power socket
protected by a suitable differential switch (thermal breaker).
The motor is equipped with a thermal overload protector
located inside the winding - this stops the compressor when
motor temperature reaches excessively high values. If the
thermal overload protector is tripped, place the switch in the
"Off" (0) position. Unplug the compressor until it has completely
cooled. When cool, reattach the plug to the power supply
and move the switch to the "On" (I) position. The compressor
should start normally. If not contact your nearest service centre
immediately.
ADJUSTING OPERATING PRESSURE
You do not have to use the maximum operating pressure at
all times. On the contrary, the pneumatic tool being used
often requires less pressure. On compressors supplied with
a pressure reducer, operating pressure must be correctly
adjusted.
Adjust pressure to the required value by turning the knob (4)
clockwise to increase pressure and anti-clockwise to reduce
it. When you have obtained optimum pressure, lock the knob
by pressing it downward. For pressure reducers equipped
without a pressure gauge, the set pressure can be seen on the
graduated scale located on the reducer body.
On pressure reducers equipped with a pressure gauge,
pressure can be seen on the gauge itself.
Advertisement
