Clear One Or More Event(S); Export And Import Events; Event Creating - Example - Lightware HDMI-TPS-TX226 User Manual

   
5.SoftwareControl-LightwareDeviceController
Condition Triggering
DIFFERENCE:
This feature is
available only for SW4-TPS-TX240-
PlusfromFWpackagev1.3.0b6.
This improvement works as if a
conditionisdetected.Whenacomplex
control system is built, a Condition may
triggernumerousActions.Atypicalexampleiswhenasystemispoweredonandthe'ready-to-use'state
has to be loaded. In this case, there could be many actions which are based on the same condition. In order
toreducethenumberofthecommands,youcantriggerone'key'condition,whichcouldstartthewhole
process.
5.10.4. Clear One or More Event(s)
Clear an Event
PresstheClear button in the Event list or in the header section in the Event editor.
Clear all Events
WhenalltheEventsmustbeclearedpresstheLoad factory defaults button above the Event list. You will be
promptedtoconfirmtheprocess.
5.10.5. Export and Import Events
The feature allows saving all the Events. The backup file can be uploaded to another HDMI-TPS-TX200
series transmitter.
Export all the Events
Step 1. PresstheExport button above the Event list.
Step 2. TheSaveasdialogboxwillappear.Setthedesiredfolderandfilename,thenpresstheSave button.
ThegeneratedfileisasimpletextfilewhichcontainsLW3protocolcommands.Thefilecanbeviewedbya
simpletexteditor,e.g.Notepad.

ATTENTION! Editingthefileisrecommendedonlyforexpertusers.
Import all the Events
Step 1. PresstheImport button above the Event list.
Step 2. TheOpendialogboxwillappear.Selectthedesiredfolderandfile,thenpresstheOpen button.
5.10.6. Event Creating - Example
Thefollowingexampleshowsyouonareal-lifesituationhowtosetupanEvent.
HDMI-TPS-TX200series–User'sManual
The Concept
TheSW4-TPS-TX240isconnectedtoaprojectorbytheTPSoutputport.Thetransmitterisalsoconnected
totheprojectorbytheRS-232portandcansendcommandsviatheserialline.Thetaskistoturnonthe
projectorwhensignalisdetectedontheTPSoutputport.
RS-232 Settings
Makesurethattheseriallineisestablishedbetweenthetransmitterandtheprojector.CheckthattheRS-232
settings of the transmitter is set exactly the same which required for the projector: baud rate, data bits,
parity,stopbits.Thetransmitterneedstobesetto:Controlprotocol:LW3;andRS-232mode:Pass-through.
SeetherelevantLDCsettingsintheRS-232
Setting the Event
Step 1. Setthecondition.
Selecttherequiredparameterstosetthecondition:
▪
▪
▪
Click on the Apply button to complete the procedure, then the condition
appearsontheuppersideintextualandLW3commandformataswell.
Step 2. Settheaction.
Iftheconditionisfulfilled,thefollowingactionneedstobelaunched:the
receiversendsacommandtotheprojectorovertheserialline:
▪
E.g.thecommandhastobeclosedwiththe<CR><LF>characterssothey
needtobeescaped.Youcanusethefollowingformatforescaping:
Inthecurrentcasethecommandis:PWR0\x0d\x0a
Selecttherequiredparameterstosettheaction:
▪
▪
▪
▪
Step 3. Enable the Event.
SelecttheE1 enabled pipe in upper left corner to set the Event as launched.
INFO:

intheWizardwheretheentireLW3structuretreeisavailable.Forexampleinsteadofsignaldetectionyou
cansetaspecifiedresolutionorcolorrangeeitherasacondition.
Appliedfirmwarepackage:v1.3.2b3 | LDCsoftware:v2.5.7b2
section.
Category:Video;
Expression:Signalisdetectedonaport;
Port:O1.
Power on - the required command which is accepted by the
projector:PWR0<CR><LF>
<command ><\x0d\x0a><command ><\x0d\x0a>...
1 2
...<command ><\x0d\x0a>
n
Category:RS-232;
Expression:SendRS-232message;
Port:P1;
Message:PWR0\x0d\x0a
Ifyoudonotfindtherequiredcategory/expression/etcwhatyouneed,choosetheAdvancedmode
59