Changing The Input Port Priority; Tps Mode Settings On Tps Ports; Sending Cec Commands - Lightware MMX8x4-HT Series User Manual


  
8. LW3 Programmers' Reference
In the above example, the Input 8 has the highest priority and Input 7 has the lowest priority on O1. On O2 O3, O4
and O5 ports the setting is the opposite.
ATTENTION! The same priority number can be set to different input ports. When the priority numbers
match, the input port with the lowest port number will have the highest priority.
INFO: Output 5 in MMX8x4-HT400MC and MMX8x4-HT420M models means the advanced analog audio
output.
8.5.16. Changing the Input Port Priority
This method required escaping the control characters. For more information see the
input can be set in the same time.
Command and Response
Ý CALL•/MEDIA/VIDEO/XP:setAutoselectionPriority(<in>\(<out>\):<prio>);(<in>\(<out>\):<prio>)
Ü mO•/MEDIA/VIDEO/XP:setAutoselectionPrioirty
Parameters
<prio> Priority number from 0 to 31, equal numbers are allowed (31 means that the port will be
skipped from the priority list).
An input port priority can be set on an output port. Many settings can be executed by
separating a semicolon (no space), see the example below.
Example
Ý CALL /MEDIA/VIDEO/
XP:setAutoselectionPriority(I1(O1):31;I2(O1):1;I3(O1):2;I4(O1):3;5(O1):4;I6(O1):5;I7(O1):6;I8(O1):7)
Ü mO /MEDIA/VIDEO/XP:setAutoselectionPriority
The Input 1 is ignored from the autoselection, priority order of the inputs are: I2, I3, I4, I5, I6, I7, I8.
8.5.17. TPS Mode Settings on TPS Ports
INFO: This command is available in MMX8x4-HT400MC and MMX8x4-HT420M models.
Command and Response #tpsmode
SET•/REMOTE/<tps_port>.tpsModeSetting=<tps_mode_setting>
Ý
pw•/REMOTE/<tps_port>.tpsModeSetting=<tps_mode_setting>
Ü
Example
Ý SET /REMOTE/S2.tpsModeSetting=A
Ü pw /REMOTE/S2.tpsModeSetting=A
MMX8x4-HT series – User's Manual
Escaping section. One or more
8.5.18. Sending CEC Commands
8.5.18.1. Sending OSD String
Parameters
Applied firmware package: v1.2.2b5 | LDC software: v2.2.1
Parameters
Identifier Parameter description
<tps_port> TPS input or output port S1-S4 for inputs
<tps_mode_setting> TPS mode
* TPS output ports are not available in MMX8x4-HT400MC model.
** Long reach and LPPF2 mode is not available in MMX8x4-HT400MC model.
For more information see section.
INFO: The hidden first 2 bit of the CEC command is static (always 04), it refers to the logical address of
the sender and the addressee. 0: sender is a TV; 4: the addressee is the Playback Device 1.
Sending the OSD string consists of two steps. First, set the CEC.OsdString property with the desired text,
after that, call the CEC.send(set_osd) method.
Step 1. Set the CEC.OsdString property.
Ý SET • /MEDIA/CEC/<port>.OsdString=<text>
Ü pw • /MEDIA/CEC/<port>.OsdString=<text>
Step 2. Call the CEC.send(set_osd) method.
Ý CALL /MEDIA/CEC/<port>:send(set_osd)
Ü mO /MEDIA/CEC/<port>:send
Parameter
Identifier
description
<port> Port identifier I1-I8: Source port number.
O1-O5: Destination port number in MMX8x4-HT-400MC
and MMX8x4-HT-420M models.
O1-O8: Destination port number in MMX8x8-HDMI-4K-A.
<text> On-screen The following characters are allowed in the text: Letters (A-Z) and (a-z),
displayed text hyphen (-), underscore (_), numbers (0-9), and dot (.). Max length: 14
characters.
Parameter values
D1-D2* for outputs
A: Auto
H: HDBaseT
L**: Longreach
1: LPPF1
2**: LPPF2
#cec
Parameter values
104