Lightware MMX8x4-HT Series User Manual page 133


  
8. LW3 Programmers' Reference
Set the Delay on Analog Audio Out
SET•/MEDIA/AUDIO/O6.Delay=<delay_status>
Ý
Set the Delay Time on Analog Audio Out
SET•/MEDIA/AUDIO/O6.Delay=<delay_time>
Ý
Equalizer (EQ) Settings on Analog Audio Out
SET•/MEDIA/AUDIO/O6.<eq_nr>Gain=<gain_value>
Ý
Save a Preset
Ý CALL /PRESETS/MICADDON/<ch>:savePreset(<index>,<target_node>,<name>)
Load a Preset
Ý CALL /PRESETS/MICADDON/<ch>:loadPreset(<index>,<target_node>)
Delete a Preset
Ý CALL•/PRESETS/MICADDON/<ch>:deletePreset(<index>)
Change the Scene Name
SET•/PRESETS/MICADDON/SCENES/<scene_id>.Name=<scene_name>
Ý
Save a Scene
Ý CALL•/PRESETS/MICADDON/SCENES:saveScene(<index>,I9,I10,I11,O6,<scene_name>)
Load a Scene
Ý CALL•/PRESETS/MICADDON/SCENES:loadScene(<index>,I9,I10,I11,O6)
Delete a Scene
Ý CALL•/PRESETS/MICADDON/SCENES:deleteScene(<index>)
Serial Port Configuration
Protocol Setting
SET•/MEDIA/UART/<serial_port>.ControlProtocol=<cont_protocol>
Ý
BAUD Rate Setting
SET•/MEDIA/UART/<serial_port>.Baudrate=<baudrate>
Ý
Operation Mode Setting
SET•/MEDIA/UART/<serial_port>.Rs232Mode=<rs232_mode>
Ý
Command Injection Mode
SET•/MEDIA/UART/<serial_port>.CommandInjectionEnable=<ci_stat>
Ý
Query the RS-232 Command Injection Port Number
Ý GET•/MEDIA/UART/<serial_port>.CommandInjectionPort
MMX8x4-HT series – User's Manual
Serial Port Messaging
Sending a Message (ASCII-format) via RS-232
Ý CALL•/MEDIA/UART/P1:sendMessage(<message>)
Sending a Text (ASCII-format) via RS-232
Ý CALL•/MEDIA/UART/P1:sendText(<message>)
Sending a Binary Message (HEX-format) via RS-232
Ý CALL•/MEDIA/UART/P1:sendBinaryMessage(<message>)
Using Hexadecimal Codes
IR Port Configuration
Enable the IR Port
SET•/MEDIA/IR/<ir_port>.Enable=<ir_port_staus>
Ý
Query the IR Command Injection Port Number
Ý GET•/MEDIA/IR/<ir_port>.CommandInjectionPort
IR Port Messaging
Sending Pronto Hex Codes in Little-endian Format via IR Port
Ý CALL /MEDIA/IR/<ir_port>:sendProntoHex(<hex_code>)
Sending Pronto Hex Codes in Big-endian Format via IR Port
Ý CALL /MEDIA/IR/<ir_port>:sendProntoHexBigEndian(<hex_code>)
Relay Port Configuration
Set Relay Connection Status
SET•/MEDIA/RELAY/<relay_port>.Output=<relay_status>
Ý
GPIO Port Settings
Set the Direction of a GPIO Pin
SET•/MEDIA/GPIO/<gpio_port>.Direction=<dir>
Ý
Set the Output Level of a GPIO Pin
SET•/MEDIA/GPIO/<gpio_port>.Output=<value>
Ý
Toggle the Level of a GPIO Pin
Ý CALL•/MEDIA/GPIO/<gpio_port>:toggle()
Applied firmware package: v1.2.2b5 | LDC software: v2.2.1
133