Lightware MMX8x4-HT Series User Manual page 131


  
8. LW3 Programmers' Reference
Query the Emulated EDIDs
Ý GET•/EDID.EdidStatus
Set the Emulated EDID
Ý CALL•/EDID:switch(<source>:<destination>)
Copy an EDID into Another Slot
Ý CALL•/EDID:copy(<source>:<destination>)
AUX Analog Audio I/O Port Settings
Audio Mode Setting
SET•/MEDIA/AUDIO/<in>.AudioMode=<audio_mode>
Ý
Mute
SET•/MEDIA/AUDIO/<in>/ADCVOLUME.Mute=<mute_status>
Ý
Volume
SET•/MEDIA/AUDIO/<in>/ADCVOLUME.VolumedB=<volume_dB>
Ý
Balance
SET•/MEDIA/AUDIO/<in>/ADCVOLUME.Balance=<balance_value>
Ý
Gain
SET•/MEDIA/AUDIO/<in>/ADCVOLUME.Gain=<gain_dB>
Ý
Mute
SET•/MEDIA/AUDIO/<in>.DACVOLUME.Mute=<mute_status>
Ý
Volume
SET•/MEDIA/AUDIO/<in>/DACVOLUME.VolumedB=<volume_dB>
Ý
Balance
SET•/MEDIA/AUDIO/<in>/DACVOLUME.Balance=<balance_value>
Ý
Advanced Audio Settings
Mute on Microphone Input
SET•/MEDIA/AUDIO/I9.Mute=<mute_status>
Ý
Set the Volume with Exact Value on Microphone Input
SET•/MEDIA/AUDIO/I9.Volume=<volume_dB>
Ý
Set the Volume by Step Value - Volume up
Ý CALL•/MEDIA/AUDIO/I9:volumeUp()
Set the Volume by Step Value - Volume down
Ý CALL•/MEDIA/AUDIO/I9:volumeDown()
MMX8x4-HT series – User's Manual
Set the Panorama on the Microphone Input
SET•/MEDIA/AUDIO/I9.Panorama=<pan_set>
Ý
Query the Gain on the Microphone Input
Ý GET•/MEDIA/AUDIO/I9.InputGain
Set the Gain n the Microphone Input
SET•/MEDIA/AUDIO/I9.InputGain=<gain_value>
Ý
Switch on the Phantom Power
SET•/MEDIA/AUDIO/I9.PhantomPower=<phantom_status>
Ý
Set the Phase Inverter on Microphone Input
SET•/MEDIA/AUDIO/I9.InvertPhase=<invertphase_status>
Ý
Set the Feedback on Microphone Input
SET•/MEDIA/AUDIO/I9.FeedbackCancel=<feedback_status>
Ý
Set the Highpass Filter on Microphone Input
SET•/MEDIA/AUDIO/I9.HPF=<hpf_status>
Ý
Set the Lowpass Filter on Microphone Input
SET•/MEDIA/AUDIO/I9.LPF=<lpf_status>
Ý
Equalizer (EQ) Settings on Microphone Input
SET•/MEDIA/AUDIO/I9.<eq_nr>Gain=<gain_value>
Ý
Load Factory Mic Preset
SET•/MEDIA/AUDIO/I9.MicPreset=<preset_nr>
Ý
Mute the Advanced Analog In
SET•/MEDIA/AUDIO/I10.Mute=<mute_status>
Ý
Set the Volume with Exact Value on Advanced Analog In
SET•/MEDIA/AUDIO/I10.Volume=<volume_dB>
Ý
Set the Volume by Step Value - Volume up
Ý CALL•/MEDIA/AUDIO/I10:volumeUp()
Set the Volume by Step Value - Volume down
Ý CALL•/MEDIA/AUDIO/I10:volumeDown()
Set the Balance on the Advanced Analog In
SET•/MEDIA/AUDIO/I10.Balance=<bal_set>
Ý
Query the Gain on the Advanced Analog In
Ý GET•/MEDIA/AUDIO/I10.InputGain
Applied firmware package: v1.2.2b5 | LDC software: v2.2.1
131