Default Tolerance Setting - Konica Minolta CM-M6 Instruction Manual

Default Tolerance Setting

… „
• The tolerance is set to the following values under the initial settings.
Memo
Lower limit: -1.00 Upper limit: 1.00
Operating Procedure
1
Move the cursor to "Default tolerance", and then
press the [Confirmation] key.
The <Default tolerance> screen is displayed.
2
Use [] or [] to move the cursor to the item to be
set, and then press the [Confirmation] key.
The <Edit tolerance> screen is displayed.
3
Use []/[] or []/[] to move the cursor to the
item to set and press the [Confirmation] key to
change the item.
• When the selected item is not currently checked,
pressing the [Confirmation] key causes the item to be
checked, after which the setting value can be changed.
• Press [] or [] to move the cursor to the setting value
area. Pressing the [Confirmation] key causes the cursor
to appear on the value. Press [] or [] to change the
value. Move the cursor between the digits of the value by
pressing [] or [].
If "Audi2000(ΔEc)" or "Audi2000(ΔEp)" is selected under
Memo
"Sample" - "Display type", not only is moving between pages
possible with the [] and [] keys from the displayed page
when the <Default tolerance> screen is selected, but if
Audi2000(ΔEc) or Audi2000(ΔEp) is enabled, in addition to
the tolerance for each angle, the tolerances for average
(mΔEc or mΔEp) and maximum (ΔEcMax or ΔEpMax) can also
be set. When setting the tolerance for mΔEc, mΔEp, ΔEcMax
or ΔEpMax, setting a value for any angle will cause that value
to be shown for all angles in the tolerance setting screen.
Settings
ΔL*, Δa*, Δb*, ΔC*, ΔH*, ΔFF: -20.00 to 20.00
{ „
Other than the above: 0.00 to 20.00
{ „
• Press the [Confirmation] key to confirm every time the
setting of an item is changed.
4
After all settings have been configured, use [] or
[] to move the cursor to "OK", and then press the
[Confirmation] key.
The setting is confirmed and the screen returns to the
<Default tolerance> screen.
If [ESC] is pressed during setup, the settings will not be
changed and the screen will return to the <Default
tolerance> screen.
5
Press [ESC] to return to the <Default data setup> screen.
81
Start the procedure from the <Default data setup> screen.
Sample
0002 TARGET-2
Setting
Default data setup
Default tolerance
Warning level
80%
Parametric coef.
Target
0002 TARGET-2
Default tolerance
1.00
None
10°/D65 ∆FF
1 2
-1.00
∆E*ab ∆L* ∆C* ∆H*
1.00 1.00 1.00 1.00
-15°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
15°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
25°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
45°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
75°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
110°
0.00 -1.00 -1.00 -1.00
Target
0002 TARGET-2
Default tolerance
1.00
Edit tolerance
None
1 10°/D65 ∆FF
2
-1.00
-15°
∆E*ab ∆L* ∆C* ∆H*
1.00 1.00 1.00 1.00
∆E*ab +01 .0 0
-15°
0.00 -1.00 -1.00 -1.00
1.00 1.00 +00 .0 0 1.00 1.00
15°
0.00 -1.00 -1.00 -1.00
∆L* 1.00 1.00 +01 .0 0 1.00 1.00
25°
0.00 -1.00 -1.00 -1.00
- 00 .0 0
1.00 1.00 1.00 1.00
45°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
75°
0.00 -1.00 -1.00 -1.00
1.00 1.00 1.00 1.00
110°
0.00 -1.00 -1.00 -1.00