Certifications For Use In Potentially Explosive Environments; Ul Haz. Loc. Certifications - B&R Panel PC 2100 User Manual

Standards and certifications • Certifications
Model number Description
5CFAST.128G-10 CFast card, 128 GB MLC
5ACCIF01.FPLS-000 Interface card - 1x RS232 interface - 1x POWERLINK interface - 32 kB FRAM - For APC2100/PPC2100
5ACCIF01.FPSC-000 Interface card - 1x RS232 interface - 1x CAN interface - 1x POWERLINK interface - 32 kB FRAM - For APC2100/PPC2100
0TB103.9 Connector 24 VDC - 3-pin female - Screw clamp terminal block 3.31 mm²
0TB103.91 Connector 24 VDC - 3-pin female - Cage clamp terminal block 3.31 mm²
0TB1210.3100 Connector - Female 10-pin - Cage clamp - Protected against vibration by the screw flange
The certificate for Germanischer Lloyd can be downloaded here:
GL certificate no.: 14 958 - 15 HH
The certificate for the compass safe distance can be downloaded here:
BSH certificate no.: 914

2.4 Certifications for use in potentially explosive environments

2.4.1 UL Haz. Loc. Certifications

Ind.Cont.Eq.
for Haz.Locs.
Cl. I, Div. 2,
Groups ABCD
E180196 (T4)
2.4.1.1 General safety guidelines
PPC2100 systems with AP923 or AP1000 display units that are certified for use in potentially explosive environ-
ments and carry the marking above are suitable for use in Class 1, Division 2, Groups A, B, C and D or in nonex-
plosive environments and correspond to the following standards: UL 508 - 17th Edition, ANSI/ISA 12.12.01:2013,
CSA C22.2 No. 213-M1987, and CSA C22.2 No. 157-92 (R2012).
2.4.1.2 Mounting and installation
Devices with explosion protection are to be used as intended and are only permitted to be operated by knowledge-
able and qualified personnel according to these operating instructions and the other information contained in the
corresponding user's manual. Operation in any other way endangers the safety and functionality of the devices
and the connected systems. The operator is responsible for following all applicable safety and accident prevention
regulations, as well as adhering to standards.
Devices must be installed in a suitable protective housing that can only be opened by using a tool. In order to
guarantee sufficient air circulation, allow the specified amount of space around the device. Use only in environments
with pollution degree 2. The maximum ambient temperature varies depending on the individual components being
used, see section "Temperature specifications" on page 28.
The certification marking on the device must be checked before each installation or use of the device in potentially
explosive environments. Additional equipment must be suitable for the operating location. Final assembly must be
approved by the relevant local authorities. Wiring must follow national regulations and meet all legal requirements.
Devices must remain voltage-free until installation work is complete. The tightening torque for the power supply
terminals is 0.5 Nm. Cables must be able to handle a surface temperature of 75°C. PPC2100 systems with AP923
or AP1000 display units are only permitted to operated with 24 VDC.
Unshielded/Ungrounded cables are never permitted to be used in potentially explosive areas. Devices must be
securely connected to the potential offset. Power supply, communication and accessory cables must be secured
on the device or control cabinet. Power supply, communication and accessory cables are not permitted to exert
excessive tensile stress on the interfaces. Possible vibrations in the environment must be taken into account for this.
250
Products with this mark have been certified by Underwriters Laboratories and are
listed as "Industrial Control Equipment for Use in Hazardous Locations". This mark
is valid for the USA and Canada and simplifies the certification of your machines and
systems in these regions.
Underwriters Laboratories (UL) in accordance with standard ANSI/ISA 12.12.01:2013
Canadian (CSA) standard in accordance with C22.2 No. 213-M1987
GL beginning
with rev.
D0
D0
D0
D0
D0
D0
Panel PC 2100 user's manual V1.11