Mitsubishi Electric GOT1000 Series Connection Manual page 362

11.5.4 Connecting to DB1000,
DB2000 Series

Communication settings
Set the communication settings with controller key
operation.
Item
Protocol
Function
*1
Station No.
*2
Transmission speed
Character
*1 Avoid duplication of the station No. with any of the other
units.
*2 Adjust the settings with GOT settings.
11.5.5 Connecting to GT120 Series

Key Lock setting
To write the Digital and the Analog parameters, set the
Key Lock setting to Lock 3.

Communication settings
Release the controller lock function in advance and set
the following communication settings.
After completing the communication settings, set the
Key Lock setting to Lock 3.
Item
Communication protocol
*1
Station No.
*2
Transmission speed
Data bit
*2
Stop bit
*2
Parity bit
*1 Avoid duplication of the station No. with any of the other
units.
*2 Adjust the settings with GOT settings.
11 - 28
11. CONNECTION TO CHINO CONTROLLER
11.5 Controller Side Setting
Set value
MODBUS (RTU)
Com: Upper communication
01 to 99
9600bps, 19200bps, 38400bps
7BIT/EVEN/STOP1
7BIT/EVEN/STOP2
7BIT/ODD/STOP1
7BIT/ODD/STOP2
8BIT/NON/STOP1
8BIT/NON/STOP2
8BIT/EVEN/STOP1
8BIT/EVEN/STOP2
8BIT/ODD/STOP1
8BIT/ODD/STOP2
Set value
comr: MODBUS RTU
1 to 95
96: 9600bps
192: 19200bps
8bits (fixed)
1bit, 2bits
nonE: None
EVEn: Even
odd: Odd
11.5.6 Connecting to KP1000,
KP2000

Key Lock setting
To write the Digital and the Analog parameters, set the
Key Lock setting.

Communication settings
Set the communication settings with controller key
operation.
Item
Protocol
Function
*1
Station No.
*2
Transmission speed
*2
Character
(Bit length, Parity bit, Stop bit)
*1 Avoid duplication of the station No. with any of the other
units.
*2 Adjust the settings with GOT settings.
11.5.7 Connecting to AL3000,
AH3000

Key Lock setting
To write the Digital and the Analog parameters, set the
Key Lock setting.

Communication settings
Set the communication settings with controller key
operation.
Item
Protocol
Transmission code
Communication type
*1
Station No.
*2
Transmission speed
*2
Character
(Bit length, Parity bit, Stop bit)
*1 Avoid duplication of the station No. with any of the other
units.
*2 Adjust the settings with GOT settings.
Set value
MODBUS (RTU)
COM
1 to 99
2400bps, 4800bps, 9600bps,
19200bps, 38400bps
8BIT/NON/STOP1
8BIT/NON/STOP2
8BIT/EVEN/STOP1
8BIT/EVEN/STOP2
8BIT/ODD/STOP1
8BIT/ODD/STOP2
Set value
MODBUS
rtu
RS232C, RS-422A, RS-485
1 to 31
2400bps, 4800bps, 9600bps,
19200bps
[8N1]: 8bit, None, 1bit
[8N2]: 8bit, None, 2bit
[8E1]: 8bit, Even, 1bit
[8E2]: 8bit, Even, 2bit
[8O1]: 8bit, Odd, 1bit
[8O2]: 8bit, Odd, 2bit