ProMinent DULCOMETER Assembly And Operating Instructions Manual page 121

More symbols . . . . . . . . . . . . . . . . . . 2
Mounting (mechanical) . . . . . . . . . . . 20
Mounting kit . . . . . . . . . . . . . . . . . . . 22
Mounting materials . . . . . . . . . . . . . . 20
Mounting position . . . . . . . . . . . . . . . 19
N
Noise generation . . . . . . . . . . . . . . 104
Non-discriminatory approach . . . . . . . . 2
O
Operating elements . . . . . . . . . . . . . 50
Original Prominent cable . . . . . . . . . . 32
Overview of equipment . . . . . . . . . . 50
P
Pipe bracket . . . . . . . . . . . . . . . . . . 21
Pipe diameter . . . . . . . . . . . . . . . . . 21
plant rooms . . . . . . . . . . . . . . . . . . 104
Preparing the control panel . . . . . . . . 23
Profile seal . . . . . . . . . . . . . . . . . . . 25
Punch out threaded holes . . . . . . . . . 39
Q
Question: Does the control have to be
adjusted during commissioning? . . . . 45
Question: Does the system have tem‐
perature compensation? . . . . . . . . . . 92
Question: How are the unit and
sensor calibrated? . . . . . . . . . . . . . . 56
Question: How do I calibrate the sen‐
sor's zero point? . . . . . . . . . . . . . . . . 64
Question: How do I vent the pump, for
example? . . . . . . . . . . . . . . . . . . . . 90
Question: How is initial commis‐
sioning done? . . . . . . . . . . . . . . . . . 45
Question: How should the controller
be mounted in terms of its reading,
mounting and operating position? . . . . 19
Question: How should the sensor
cable be assembled? . . . . . . . . . . . . 31
Question: Is there a legend for the
"Wiring" table? . . . . . . . . . . . . . . . . . 32
Question: What applications is the
controller intended for? . . . . . . . . . . . 17
Question: What can be calibrated? . . . 56
Question: What can the output relays
do? . . . . . . . . . . . . . . . . . . . . . . . . . 17
Question: What control direction is
available? . . . . . . . . . . . . . . . . . . . . 17
Question: What do I have to consider
in terms of recycling? . . . . . . . . . . . . 19
Question: What do the LEDs indicate? 17
Question: What happens in the event
of incorrect calibration? . . . . . . . . . . . 57
Question: What information is made
available in the continuous display? . . 53
Question: What information is made
available in the info display? . . . . . . . 54
Question: What is the load capacity of
the hinge? . . . . . . . . . . . . . . . . . . . . 18
Question: What needs to be consid‐
ered in terms of accessibility? . . . . . . 18
Question: When are the actuators
reset to factory settings? . . . . . . . . . . 45
Question: Where can I find the Decla‐
ration of Conformity? . . . . . . . . . . . . 118
Question: Which cable is connected
to which threaded connector? . . . . . . 32
Question: Which measured variables
can be processed? . . . . . . . . . . . . . . 17
Index
121