Subaru IMPREZA GD 2007 Series Manual page 1657

asieps_tobira_IM_US.book 326 ページ ２０１２年１月１７日 火曜日 午後３時４８分
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
ENGINE (DIAGNOSTICS)
Step
13 CHECK SENSOR OUTPUT.
Read the data of sub throttle sensor signal
using Subaru Select Monitor.
NOTE:
Subaru Select Monitor
For detailed operation procedures, refer to
"READ CURRENT DATA FOR ENGINE". <Ref.
to EN(STI)(diag)-33, Subaru Select Monitor.>
14 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL MOTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM and
electronic throttle control.
3) Measure the resistance between ECM and
electronic throttle control connector.
Connector & terminal
(B137) No. 5 — (E57) No. 2:
(B137) No. 4 — (E57) No. 1:
15 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL MOTOR.
1) Connect the ECM.
2) Turn the ignition switch to ON.
3) Measure the voltage between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 2 (+) — Engine ground (–):
(E57) No. 1 (+) — Engine ground (–):
16 CHECK HARNESS BETWEEN ECM AND
ELECTRONIC THROTTLE CONTROL MOTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from the ECM.
3) Measure the resistance between electronic
throttle control connector and engine ground.
Connector & terminal
(E57) No. 2 — Engine ground:
(E57) No. 1 — Engine ground:
17 CHECK ELECTRONIC THROTTLE CON-
TROL MOTOR HARNESS.
Measure the resistance between the electronic
throttle control connector terminals.
Connector & terminal
(E57) No. 2 — (E57) No. 1:
18 CHECK ELECTRONIC THROTTLE CON-
TROL GROUND CIRCUIT.
Measure the resistance between ECM and
chassis ground.
Connector & terminal
(B134) No. 5 — Chassis ground:
(B137) No. 1 — Chassis ground:
(B137) No. 2 — Chassis ground:
(B137) No. 3 — Chassis ground:
(B137) No. 7 — Chassis ground:
19 CHECK ELECTRONIC THROTTLE CONTROL.
Measure the resistance between electronic
throttle control terminals.
Terminals
No. 2 — No. 1:
Check
Is the voltage 1.64 — 1.70 V?
Is the resistance less than 1 Ω? Go to step 15.
Is the voltage 5 V or more?
Is the resistance 1 MΩ or more? Go to step 17.
Is the resistance 1 MΩ or more? Go to step 18.
Is the resistance less than 5 Ω? Go to step 19.
Is the resistance 50 Ω or less? Go to step 20.
EN(STI)(diag)-326
Yes No
Go to step 14. Repair poor con-
tact of the elec-
tronic throttle
control connector.
Replace the elec-
tronic throttle con-
trol if defective.
<Ref. to
FU(H4DOTC)-16,
Throttle Body.>
Repair the open
circuit of harness
between ECM and
electronic throttle
control.
Go to step 16.
Repair the short
circuit to power in
the harness
between the ECM
and electronic
throttle control.
Repair the ground
short circuit of har-
ness between the
ECM and elec-
tronic throttle con-
trol.
Repair the short
circuit in the har-
ness between the
ECM and elec-
tronic throttle con-
trol.
Repair the open
circuit of the har-
ness between the
ECM and engine
ground.
Replace the elec-
tronic throttle con-
trol. <Ref. to
FU(H4DOTC)-16,
Throttle Body.>