Usb 2.0 Ulpi Transceiver - Xilinx VC707 User Manual

Chapter 1: VC707 Evaluation Board Features
X-Ref Target - Figure 1-4
GND

USB 2.0 ULPI Transceiver

[Figure
The VC707 board uses a Standard Microsystems Corporation USB3320 USB 2.0 ULPI
Transceiver (U8) to support a USB connection to the host computer. A USB cable is
supplied in the VC707 Evaluation Kit (type-A connector to host computer, mini-B
connector to VC707 board connector J2).
The USB3320 is a high-speed USB 2.0 PHY supporting the UTMI+ low pin interface (ULPI)
interface standard. The ULPI standard defines the interface between the USB controller IP
and the PHY device which drives the physical USB bus. Use of the ULPI standard reduces
the interface pin count between the USB controller IP and the PHY device.
18
U3
PC28F00AG18FE
64-Pin BGA (8 x 10 mm)
FLASH_D0_R F2
DQ0
FLASH_D1_R E2
DQ1
FLASH_D2_R G3
DQ2
FLASH_D3_R E4
DQ3
FLASH_D4_R
E5
DQ4
FLASH_D5_R G5
DQ5
FLASH_D6_R
G6
DQ6
FLASH_D7_R H7
DQ7
FLASH_D8_R
E1
DQ8
FLASH_D9_R E3
DQ9
FLASH_D10_R F3
DQ10
FLASH_D11_R F4
DQ11
FLASH_D12_R F5
DQ12
FLASH_D13_R H5
DQ13
FLASH_D14_R G7
DQ14
FLASH_D15_R E7
DQ15
FLASH_PWE_B G8
WE_B
FLASH_WP_B C6
WP_B
FLASH_ADV_B
F6
ADV_B
FPGA_INIT_B D4
RST_B
FLASH_OE_B
F8
OE_B
FLASH_CE_B
B4
CE_B
FLASH_WAIT_R
F7
WAIT
E6
FPGA_CCLK
CLK
NC E8
RFU1
NC F1
RFU2
NC G2
RFU3
B2
VSS0
H2
VSS1
H4
VSS2
H6
VSS3
Figure 1-4: 128 MB Linear Flash Memory (U3)
1-2, callout 4]
www.xilinx.com
A1 FLASH_A0
A1
FLASH_A1
B1
A2
FLASH_A2
C1
A3
FLASH_A3
D1
A4
FLASH_A4
D2
A5
FLASH_A5
A2
A6
FLASH_A6
C2
A7
FLASH_A7
A3
A8
FLASH_A8
B3
A9
FLASH_A9
C3
A10
FLASH_A10
D3
A11
FLASH_A11
A12 C4
FLASH_A12
A5
A13
B5 FLASH_A13
A14
FLASH_A14
C5
A15
FLASH_A15
D7
A16
FLASH_A16
D8
A17
FLASH_A17
A7
A18
FLASH_A18
B7
A19
FLASH_A19
C7
A20
FLASH_A20
C8
A21
FLASH_A21
A8
A22
FLASH_A22
G1
A23
FLASH_A23
H8
A24
FLASH_A24
A25 B6
FLASH_A25
B8
A26
H1 NC
A27
D5
VCCQ1
D6
VCCQ2
1.8V
G4
VCCQ3
A4
VPP
A6
1.8V
VCC1
H3
VCC2
UG885_c1_04_021012
UG885 (v1.2) February 1, 2013
VC707 Evaluation Board