Siemens sinumerik 840D sl Operating Manual page 12
Turning
Hide thumbs
Also See for sinumerik 840D sl:
- Function manual (2184 pages) ,
- Programming manual (1334 pages) ,
- Commissioning manual (1102 pages)
Table of Contents
Advertisement
Table of contents
8.4.1
Face milling (CYCLE61)............................................................................................................ 333
8.4.2
Rectangular pocket (POCKET3)............................................................................................... 336
8.4.3
Circular pocket (POCKET4) ...................................................................................................... 340
8.4.4
Rectangular spigot (CYCLE76)................................................................................................. 345
8.4.5
Circular spigot (CYCLE77)........................................................................................................ 348
8.4.6
Multi-edge (CYCLE79) .............................................................................................................. 351
8.4.7
Longitudinal groove (SLOT1) .................................................................................................... 353
8.4.8
Circumferential groove (SLOT2) ............................................................................................... 357
8.4.9
Open groove (CYCLE899) ........................................................................................................ 361
8.4.10
Long hole (LONGHOLE) - only for G code program................................................................. 368
8.4.11
Thread milling (CYCLE70) ........................................................................................................ 370
8.4.12
Engraving (CYCLE60)............................................................................................................... 373
8.5
Contour milling .......................................................................................................................... 380
8.5.1
General information................................................................................................................... 380
8.5.2
Representation of the contour................................................................................................... 380
8.5.3
Creating a new contour ............................................................................................................. 382
8.5.4
Creating contour elements ........................................................................................................ 384
8.5.5
Changing the contour................................................................................................................ 389
8.5.6
Contour call (CYCLE62) - only for G code program ................................................................. 390
8.5.7
Path milling (CYCLE72) ............................................................................................................ 391
8.5.8
Contour pocket/contour spigot (CYCLE63/64).......................................................................... 395
8.5.9
Predrilling contour pocket (CYCLE64) ...................................................................................... 397
8.5.10
Milling contour pocket (CYCLE63)............................................................................................ 401
8.5.11
Contour pocket residual material (CYCLE63, option)............................................................... 404
8.5.12
Milling contour spigot (CYCLE63)............................................................................................. 406
8.5.13
Contour spigot residual material (CYCLE63, option)................................................................ 409
8.6
Further cycles and functions ..................................................................................................... 412
8.6.1
Swiveling plane/tool (CYCLE800)............................................................................................. 412
8.6.2
Swiveling tool (CYCLE800)....................................................................................................... 420
8.6.2.1
Orienting turning tools - only for G code program (CYCLE800) ............................................... 420
8.6.2.2
Orienting milling tools - only for G code program (CYCLE800) ................................................ 421
8.6.2.3
Preloading milling tools - only for G code program (CYCLE800) ............................................. 422
8.6.3
High-speed settings (CYCLE832)............................................................................................. 424
8.6.4
Subroutines ............................................................................................................................... 425
8.7
Further cycles and functions ShopTurn .................................................................................... 428
8.7.1
Drilling centric............................................................................................................................ 428
8.7.2
Thread centered........................................................................................................................ 430
8.7.3
Transformations ........................................................................................................................ 432
8.7.4
Translation................................................................................................................................. 434
8.7.5
Rotation ..................................................................................................................................... 435
8.7.6
Scaling....................................................................................................................................... 436
8.7.7
Mirroring .................................................................................................................................... 437
8.7.8
Rotation C ................................................................................................................................. 438
8.7.9
Straight and circular machining................................................................................................. 439
8.7.10
Selecting a tool and machining plane ....................................................................................... 440
8.7.11
Programming a straight line ...................................................................................................... 442
8.7.12
Programming a circle with known center point ......................................................................... 444
8.7.13
Programming a circle with known radius .................................................................................. 446
8.7.14
Polar coordinates ...................................................................................................................... 448
8.7.15
Straight line polar ...................................................................................................................... 449
8.7.16
Circle polar ................................................................................................................................ 451
8.7.17
Machining with the counterspindle............................................................................................ 452
counterspindle........................................................................................................................... 454
12
Operating Manual, 07/2010, 6FC5398-8CP40-0BA0
Turning
Advertisement
Table of Contents
