Mitsubishi Electric MR-J4-10B(-RJ) Instruction Manual page 11

3.7.1 When you use the forced stop deceleration function ................................................................ 3-33
3.7.2 When you do not use the forced stop deceleration function ..................................................... 3-34
3.8 Interfaces ......................................................................................................................................... 3-35
3.8.1 Internal connection diagram ...................................................................................................... 3-35
3.8.2 Detailed explanation of interfaces ............................................................................................. 3-36
3.8.3 Source I/O interfaces ................................................................................................................ 3-38
3.9 SSCNET III cable connection .......................................................................................................... 3-39
3.10 Servo motor with an electromagnetic brake .................................................................................. 3-41
3.10.1 Safety precautions .................................................................................................................. 3-41
3.10.2 Timing chart ............................................................................................................................ 3-42
3.11 Grounding ...................................................................................................................................... 3-46
4. STARTUP
4.1 Switching power on for the first time ................................................................................................. 4- 2
4.1.1 Startup procedure ...................................................................................................................... 4- 2
4.1.2 Wiring check ............................................................................................................................... 4- 3
4.1.3 Surrounding environment ........................................................................................................... 4- 6
4.2 Startup .............................................................................................................................................. 4- 6
4.3 Switch setting and display of the servo amplifier .............................................................................. 4- 8
4.3.1 Switches ..................................................................................................................................... 4- 8
4.3.2 Scrolling display ........................................................................................................................ 4-11
4.3.3 Status display of an axis ........................................................................................................... 4-12
4.4 Test operation .................................................................................................................................. 4-14
4.5 Test operation mode ........................................................................................................................ 4-14
4.5.1 Test operation mode in MR Configurator2 ................................................................................ 4-15
4.5.2 Motor-less operation in controller .............................................................................................. 4-18
5. PARAMETERS
5.1 Parameter list .................................................................................................................................... 5- 1
5.1.1 Basic setting parameters ([Pr. PA_ _ ]) ...................................................................................... 5- 2
5.1.2 Gain/filter setting parameters ([Pr. PB_ _ ]) ............................................................................... 5- 3
5.1.3 Extension setting parameters ([Pr. PC_ _ ]) .............................................................................. 5- 4
5.1.4 I/O setting parameters ([Pr. PD_ _ ]) ......................................................................................... 5- 6
5.1.5 Extension setting 2 parameters ([Pr. PE_ _ ]) ............................................................................ 5- 7
5.1.6 Extension setting 3 parameters ([Pr. PF_ _ ]) ............................................................................ 5- 8
5.1.7 Linear servo motor/DD motor setting parameters ([Pr. PL_ _ ]) ................................................ 5- 9
5.2 Detailed list of parameters ............................................................................................................... 5-11
5.2.1 Basic setting parameters ([Pr. PA_ _ ]) ..................................................................................... 5-11
5.2.2 Gain/filter setting parameters ([Pr. PB_ _ ]) .............................................................................. 5-22
5.2.3 Extension setting parameters ([Pr. PC_ _ ]) ............................................................................. 5-35
5.2.4 I/O setting parameters ([Pr. PD_ _ ]) ........................................................................................ 5-42
5.2.5 Extension setting 2 parameters ([Pr. PE_ _ ]) ........................................................................... 5-48
5.2.6 Extension setting 3 parameters ([Pr. PF_ _ ]) ........................................................................... 5-51
5.2.7 Linear servo motor/DD motor setting parameters ([Pr. PL_ _ ]) ............................................... 5-53
6. NORMAL GAIN ADJUSTMENT
6.1 Different adjustment methods ........................................................................................................... 6- 1
6.1.1 Adjustment on a single servo amplifier ...................................................................................... 6- 1
2
4- 1 to 4-20
5- 1 to 5-56
6- 1 to 6-28