GE UR Series Manual page 349

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
ProcBusFail SPS Process bus system status
ProcBusTrbl SPS Process Bus Trouble
PtpFail SPS Bad PTP Signal
RecMod ENG AR Mode setting: 1 = 1 and 3 Pole, 2 = 1 Pole, 3 = 3 Pole-A, 4 = 3 Pole-B
RefWinding INS Reference winding
RelDpo SPS This data object indicates that not all criteria are fulfilled, and the switching/operation
action is not released to proceed. Complement of Rel.
RrtdComFail SPS RRTD communication failure
Rs SPS Autoreclose has been reset either manually or by the rest timer
RsLO1 ENG Reset lockout on condition setting: 0 = Off, 1 = On, in this case on Breaker Closed
condition
RsLOTmcs ING This setting establishes how long the breaker stays closed after a manual close
command, in order for the autorecloser to reset from lockout
RsTms INS The UTC time of the last clear in seconds elapsed since 00:00:00 January 1, 1970
RtdTrbl SPS RTD Trouble
RvOp SPS Fault direction is reverse
RxGooseOff SPS One or more RxGOOSE is not responding
Sat1 SPS Indicates CT saturation is detected.
For SttDifPDIF, indicates phase saturation of differential is detected per phase.
Sat 1 SPS Indicates CT saturation is detected per phase (where the last digit of instance number
1, 2, or 3 refers to phase A, B, and C respectively)
SecEthFail SPS Second Ethernet failure
SeqDlTmcs ING Time interval allowed for a single reclose shot. Timing is started whenever reclose shot
is initiated and is active until a breaker closed signal is sent.
SeqTO SPS The incomplete sequence timer timed out
ShotCnt1 SPS Autoreclosec # shot count is equal to the number indicated by the data instance
number
ShotCnt1 SPS Autoreclosec shot count is equal to the number indicated by the data instance number Rec13pRREC
SntpFail SPS SNTP server is not responding
StrBia ACD B90 Start Biased indicates the detection of a fault or an unacceptable condition by
Biased Differential element
StrOutgoing SPS This Data Object indicates an unstable Power swing detection for outgoing Locus
StrPhs SPS Indicates the detection of a fault or an unacceptable condition on a particular phase-
to-phase loop
StrRec3p SPS Initiate a three-pole reclose
StrZ2GndDl SPS Start zone 2 ground timer
StrZ2PhDl SPS Start zone 2 phase timer
StTyp ENG Switch input status type: 0 = 3-Pole (i.e. not independent pole status), 1 = 1-Pole (i.e.
three independent pole status)
StubBusOp SPS The stub bus function is operated
SwFail SPS Autoreclose mode switching failed
SysExcp SPS System exception
TdrTrbl SPS TDR Trouble
TempMnt SPS The ambient temperature is greater than the maximum operating temperature
TgtEna1 ENG Enable generation of targets (front panel display messages) setting: 0 = Self-reset, 1 =
Latched, and 2 = Disabled
ThrdEthFail SPS Third Ethernet failure
UR SERIES – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical
nodes...
LPHD
LPHD
LPHD
Rec13pRREC
PctDifPDIF1
SynChkRSYN
LPHD
Rec13pRREC
Rec3pRREC
3
Rec3pRREC
OscRDRE
LPHD
NegDocRDIR,
NeuDocRDIR
LPHD
B_DifPDIF, SttDifPDIF
BusDifPDIF
LPHD
Rec3pRREC,
Rec13pRREC
Rec13pRREC
Rec3pRREC
LPHD
B_DifPDIF
PwrSwgRPSB1
PhsDisPDIS
TrOutPTRC
TrOutPTRC
TrOutPTRC
Bkr?XCBR,
LinDfPDIF
Rec13pRREC
LPHD
LPHD
LPHD
AuxOvPTOV,
AuxUvPTUV,
B_IocPIOC,
B_TocPTOC,
BkrFaRBRF
LPHD
3-133