GE UR Series Manual page 348

MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Data object CDC
name
LivLiv SPS
LivLivDpo SPS
LivV1 SPS
LosLife MV
LosLifeRte MV
LosPkt1 SPS
MAC VSG
MajorErr SPS
3
MaxAsymOp1 SPS
MinorErr SPS
MnlCls SPS
NegTotVArh MV
NegTotWh MV
NeutOpn SPS
NeutSupn SPS
NumCycPer INS
Off SPS
On SPS
OnePoleOpn SPS
OnePU ASG
OpBia ACT
OpHiSet ACT
OpLoSet ACT
OpnSt1 SPS
OpPhs1 SPS
OpSig MV
OpUnBia ACT
OscilGOOSE SPS
OutOfSrv SPS
P1Rip SPS
P3Rip1 SPS
P3Tr SPS
PbCtl ENG
PFLLfail SPS
PhDir1 SPS
PosTotVArh MV
PosTotWh MV
3-132
Semantics
This data object indicates that both sources are live, and that angle, frequency, and
voltage difference and range conditions have been met
This data object indicates that one or both sources are not live, or that angle,
frequency, and voltage difference and range conditions have been met
This data object indicates that V1 is above the LivVal1 setting
The lost packet threshold has been exceeded
Expected value of Destination MAC address field in messages subscribed to by
RxGOOSE#
Any of the major self-test errors generated (major error)
Asymmetry on the channel exceeded pre-set value
Any of the minor self-test errors generated (minor error)
Manual close initiated
Total VAr-hour in negative direction
Total Watt-hour in negative direction
Indicates source has lost voltage signal
Neutral overcurrent supervision status
Number of cycles of the nominal frequency
Logic 0 fixed operand
Logic 1 fixed operand
One pole is open, others closed
The per-unit base factor applied to the corresponding RxGOOSE analog input
FlexAnalog quantity to normalize it to a per-unit quantity.
B90 Operate indicates the trip decision of a biased protection logic
B90 Operate indicates the trip decision of the HISET element of breaker failure current
supervision function.
B90 Operate indicates the trip decision of the LOSET element of breaker failure current
supervision function.
Open status detected
Indicates a trip decision for a particular cause per phase
Operating signal, the analogue value used by the comparator
B90 Operate indicates the trip decision of an unbiased protection logic
One or more of GGIO1.Ind###.stVal has been frozen due to frequent status changes
(chatter) in the mapped operand
Out-of-service
Autoreclose A single pole is in progress
Autoreclose 3-pole is in progress via dead time number indicated by the data instance
number
Force any trip to 3-phase trip
Front panel pushbutton control Enable/Disable setting: 0 = Disabled, 1 = Enabled
Phase and/or frequency lock loop (PFLL) has failed
Indicates Phase Comparison of differential is satisfied per phase, where the last digit of
instance number 1, 2, or 3 refers to phase A, B, and C respectively
Total VAr-hour in positive direction
Total Watt-hour in positive direction
CHAPTER 3: IEC 61850 COMMUNICATION
Used in logical
nodes...
SynChkRSYN
SynChkRSYN
SynChkRSYN
LosLifSPTR1
LosLifSPTR1
LinDfPDIF
LGOS
LPHD
LinDfPDIF
LPHD
Bkr?XCBR
EnrMtrMMTR
EnrMtrMMTR
VtffGAPC
GndDisPDIS
OscRDRE
Master/LLN0
Master/LLN0
Bkr?XCBR
GGIO3
B_DifPDIF
B_BFaiPIOC
B_BFaiPIOC
Bkr?XCBR,
Disc0XSWI,
Disc?XSWI, GGIO3
BusDifPDIF,
PhsDisPDIS
FlxElGAPC
B_DifPDIF
LPHD
Bkr?XCBR
Rec13pRREC
Rec13pRREC
Rec13pRREC
Bkr?XCBR
LinDfPDIF
B_DifPDIF,
BusDifPDIF,
SttDifPDIF
EnrMtrMMTR
EnrMtrMMTR
UR SERIES – COMMUNICATIONS GUIDE