GE UR Series Manual page 347

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
EqLim SPS The number of pulses counted is equal to the set number
EqpMismat SPS The configuration of modules does not match the stored order code
EvtEna1 ENG Setting to enable generation of events in event record, 0 = Disabled, 1 = Enabled
EvtRcdClr SPC Clear Event Records (erase all Events), same action as command CLEAR EVENT
RECORDS?
FlexErrTkn SPS A FlexLogic equation is incorrect
FltLinID VSS Faulted line ID
FrstEthFail SPS First Ethernet failure
Function1 ENG Function Enable/Disable setting: 0 = Disabled, 1 = Enabled (note that TISSUE 670
suggests something like this named SetMod)
FwdOp SPS Fault direction is forward
GoDatSetRef ORG Expected value of datSet field in messages subscribed to by RxGOOSE#
GoEnaPort1 ENG Enable all GOOSE on Ethernet port setting: 0 = Disabled, 1 = Enabled
GoID VSG Expected value of goID field in messages subscribed to by RxGOOSE#
GpsFail1 SPS GPS failed at terminal corresponding to instance number
GrAct1 SPS Setting group corresponding to index is active
HzChgRte MV Frequency rate of change measured value
Id1 VSG Name setting
IdFail1 SPS ID check for a peer L30/L90 on the channel has failed
IndFailBeh ENG Setting to select the behavior of the RxGOOSE Boolean when the sending device is
offline: 0 = On, 1 = Off, 2 = Latest/On, 3 = Latest/Off
IndPos DPS Generic remote DPS input status values: 0 for intermediate-state, 1 for off, 2 for on, 3 for
bad-state
InitMod ENG Initiate mode setting: 0 = Protection and CB, 1 = Protection Only
IntermSt1 SPS Intermediate-status detected
IrigbFail SPS A bad IRIG-B input signal has been detected
IsoBlk ACT B90 - Indicates that the isolator position is invalid
IsoPos ACT B90 - Indicates position of isolator. When "On", the related current is included in
differential zone; when "Off", the current is excluded from differential calculations.
LastSqNum INS Last sequence number received
LatchErr SPS A difference is detected between the desired and actual latch contact state
LeoSt SPS Line end open status
LivDea SPS This data object indicates that live/dead conditions have been met
LivDeaDpo SPS This data object indicates that live/dead conditions have not been met
UR SERIES – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical
nodes...
DigCntFCNT
LPHD
Rec3pRREC,
Rec13pRREC,
AuxOvPTOV,
AuxUvPTUV,
B_IocPIOC,
B_TocPTOC,
Bkr?XCBR,
BkrFaRBRF, GGIO3,
NegDocRDIR
Master/LLN0
3
LPHD
FltRFLO
LPHD
Rec3pRREC,
Rec13pRREC,
AuxOvPTOV,
AuxUvPTUV,
B_IocPIOC,
B_TocPTOC,
Bkr?XCBR, Master/
LLN0, GGIO2,
TrBusPTRC
NegDocRDIR,
NeuDocRDIR
LGOS
Master/LLN0
LGOS
LinDfPDIF
Master/LLN0 (not in
C30)
RteHzPFRC
ACsrcMMXU,
Bkr?XCBR,
FlxLgcGAPC, GGIO2
LinDfPDIF
GGIO3
GGIO3
Rec13pRREC
Bkr?XCBR,
Disc?XSWI, GGIO3
LPHD
B_IsoSSWI
B_IsoSSWI
LGOS
LPHD
LinPkpPIOC
SynChkRSYN
SynChkRSYN
3-131