YASKAWA CIMR-VU BA0001 Technical Manual page 506

Index
S
Safe Disable Input ..........................................................64, 481
Safe Disable Signal Input...................................................... 285
Safety Hazard Definitions .......................................................13
Safety Information................................................................13
SC ........................................................................... 264, 279
S-Curve Characteristic at Accel End ......................................... 362
S-Curve Characteristic at Accel Start ........................................ 362
S-Curve Characteristic at Decel End ......................................... 362
S-Curve Characteristic at Decel Start ........................................ 362
S-Curve Characteristics ........................................................ 262
SE ........................................................................... 266, 289
Search Operation Voltage Limit .............................................. 361
SEr .......................................................................... 264, 279
Serial Communication Terminals...............................................65
Serial Communication Transmission Error ........................... 265, 282
Setup Mode ................................................................... 86, 89
Shielded Twisted-Pair Cables ...................................................67
Short-Circuit Brake............................................................. 380
Short-Circuit Brake (N.C.) .................................................... 378
Short-Circuit Brake (N.O.) .................................................... 378
Short Circuit Brake Time at Start............................................. 357
Side-by-Side Setup ...............................................................39
Sinking/Sourcing Mode Switch.................................................34
Slip Compensation Gain ................................................. 261, 362
Slip Compensation Limit ...................................................... 362
Slip Compensation Primary Delay Time .................................... 362
Slip Compensation Primary Delay Time Constant......................... 261
Slip Compensation Selection during Regeneration ........................ 362
Soft Charge Bypass Relay Maintenance Time........................ 265, 286
Soft Charge Circuit Fault ...................................................... 264
Soft Current Limit Selection .................................................. 390
Soft Starter Speed Reference at Previous Fault............................. 401
Software No. (Flash) ........................................................... 400
Software No. (ROM) ........................................................... 400
Speed Agreement Detection Level ........................................... 387
Speed Agreement Detection Level (+/-) ..................................... 387
Speed Agreement Detection Width .......................................... 387
Speed Agreement Detection Width (+/-) .................................... 387
Speed Deviation (for Simple V/f with PG)............................ 270, 283
Speed Feedback Detection Control (AFR) Gain ........................... 392
Speed Feedback Detection Control (AFR) Time Constant................ 392
Speed Feedback Detection Control (AFR) Time Constant 2 ............. 392
Speed Feedback Detection Control [AFR] Time Constant 1 ............. 306
Speed Feedback Detection Control Gain .................................... 393
Speed Feedback Detection Control Gain during ov Suppression ........ 393
Speed Feedback Detection Suppression Gain............................... 307
Speed Search .................................................................... 380
Speed Search Deactivation Current .......................................... 358
Speed Search Deceleration Time ............................................. 358
Speed Search Delay Time ..................................................... 358
Speed Search Induced Voltage Level ........................................ 358
Speed Search Method Selection .............................................. 358
Speed Search Restart Current Level.......................................... 358
Speed Search Restart Detection Time........................................ 358
Speed Search Retry Interval Time............................................ 358
Speed Search Selection at Start ............................................... 358
Stall Prevention ................................................................. 262
Stall Prevention During Deceleration ..........................................73
506
Stall Prevention Level during Acceleration ................................. 385
Stall Prevention Level during Run ........................................... 386
Stall Prevention Limit during Acceleration ................................. 385
Stall Prevention Selection during Acceleration............................. 385
Stall Prevention Selection during Deceleration............................. 386
Stall Prevention Selection during Run ....................................... 386
Standard Connection Diagram ............................................. 50, 51
Stationary Auto-Tuning........................................................ 103
STo ......................................................................... 264, 279
STo Deviation Detection ...................................................... 391
STo Fault Detection Level..................................................... 391
STOP button Input........................................................ 266, 296
STOP Key Function Selection ................................................ 394
Stopping Method After Communication Error ............................. 383
Suppression Diode Connection .................................................65
T
T1-00 ............................................................................. 398
T1-01 ....................................................................... 102, 398
T1-02 ....................................................................... 105, 398
T1-03 ....................................................................... 105, 398
T1-04 ....................................................................... 105, 398
T1-05 ....................................................................... 105, 398
T1-06 ....................................................................... 105, 398
T1-07 ................................................................. 105, 106, 398
T1-11 ............................................................................. 398
Terminal A1/A2 Enable........................................................ 376
Terminal A1 Bias Setting...................................................... 381
Terminal A1 Gain Setting ..................................................... 381
Terminal A1 Signal Level Selection ......................................... 381
Terminal A2 Bias Setting...................................................... 381
Terminal A2 Function Selection.............................................. 381
Terminal A2 Gain Setting ..................................................... 381
Terminal A2 Signal Level Selection ......................................... 381
Terminal Block Configuration ..................................................54
Terminal Board ................................................................. 319
Terminal Board Communications Error ..................................... 268
Terminal Board Not Connected............................................... 270
Terminal Board Wiring Guide ..................................................67
Terminal MA, MB and MC Function Selection (relay) ................... 378
Terminal P1 Function Selection (open-collector) .......................... 378
Terminal P2 Function Selection (open-collector) .......................... 378
Test Run............................................ 102, 103, 104, 105, 106, 108
Tightening Torque ................................................................58
Timer Function Input........................................................... 377
Timer Function Off-Delay Time.............................................. 358
Timer Function On-Delay Time .............................................. 358
Timer Output .................................................................... 379
Timing Fault............................................................... 264, 269
T Motor Tuning ................................................................. 398
Too Many Speed Search Restarts....................................... 264, 279
Torque Compensation at Forward Start...................................... 363
Torque Compensation at Reverse Start ...................................... 363
Torque Compensation Gain ............................................. 260, 363
Torque Compensation Gain - Motor 2 ....................................... 370
Torque Compensation Primary Delay Time .............. 260, 306, 307, 363
Torque Compensation Primary Delay Time Constant 1................... 261
Torque Compensation Primary Delay Time Constant 2................... 261
Torque Compensation Time Constant ....................................... 363
Torque Detection 1 (N.O.)..................................................... 379
YASKAWA ELECTRIC SIEP C710606 18F YASKAWA AC Drive – V1000 Technical Manual