Command And Response Table For Dsp Sis Commands - Extron electronics mediaport 200 User Manual

Command and Response Table for DSP SIS Commands

Command
NOTE: The command format is the same regardless of the control to be set. The acceptable adjustment range varies
depending on the control or mix-point (see the
Audio Level Control and Processor Configuration
NOTE: The dB values of the level settings are in 0.1 dB increments allowing negative numbers but not decimal places.
Multiply the desired level setting by 10 for the SIS command value.
Example: To set an input level to 45.2 dB, use 452. To set an input level to -12.5 dB, use -125.
Set gain
Example 1 (Input 3 gain):
Example 2 (Output 5 gain):
Read gain
Example 1 (Output 1):
Example 2 (Input 1):
Audio Mute
Audio mute
Example:
Audio unmute
Read audio mute or level
Phantom Power
Enable or disable phantom
power
View phantom power
X10@
NOTE: = Processor type range (object ID or OID, see the
X10#
= CdB value in 0.1 dB increments. Use negative numbers for attenuation. Decimal places are invalid. The
valid range depends on the type of block specified for X10@ in the gain command (see the
Level table
X10^
= Mute status of signal: 0 = unmuted (pass), 1 = muted
X10(
= Phantom power status: 0 = standard power (phantom power off), 1 = phantom power on (default)
ASCII Command
(Host to Processor)
level control and processor selection tables
E X10@ X10# }
g * AU
NOTE: For attenuation, use negative gain values (–g).
E }
g 40002 * –8 AU
E }
g 60004 * 165 AU
E X10@ }
g AU
E }
g 60000 AU
E }
g 40000 AU
E X10@ }
m *1 AU
E }
m 40003 * 1 AU
E X10@ }
m * 0 AU
E X10@ }
m AU
E X10@ X10( }
z * AU
E X10@ }
z AU
on page 68 for the gain range of each processor).
Response
(Processor to Host)
X10@ X10# ]
DsG
*
]
DsG 40002 * –8
]
DsG 60004 * 165
X10@ X10# ]
DsG
*
]
DsG 60000 * 55
]
DsG 40000 * 92
X10@ ]
DsM 1
*
]
DsM 40003 1
*
X10@ ]
DsM 0
*
X10^ ]
With tagged responses
(verbose modes 2 and 3):
X10@ X10^ ]
DsM
*
X10@ X10( ]
DsZ *
X10@ X10( ]
*
Processor Indicator Type table
MediaPort 200 • Remote Configuration and Control
Additional Description
X10@
for on page 68).
X10@
Set trim or mix control
(see level block numbers
table on page 68) to
X10# dB (see Gain, trim,
or attenuation level
symbol definitions on
page 68).
Set input 3 gain to -0.8 dB.
Set output 5 to +16.5 dB.
View DSP gain level
X10#
dB, set for gain
X10@
control .
Output 1 is set to +5.5 dB.
Input 1 is set to +9.2 dB.
X10@
Mute audio point .
Mute input 4.
Unmute audio point X10@ .
X10^
View mute status of
X10@
input .
Set phantom power to
X10( X10@
for block .
on page 68).
P
rocessor Gain
70