MIMAKI TX500-1800DS Operation Manual page 172

Message
E R ROR 6 2 7
I N S E R T C A R T R I DG E
E R ROR 5 0 5
ME D I A J AM
E R ROR 5 0 c
ME D I A W I D T H S E N S OR
E R ROR 5 0 9
HDC POS CN T
E R ROR 5 0 a
Y OR I G I N
E R ROR 5 0 f
L - S C A L E B L A C K
E R ROR 5 1 9
N E G A T I V E P . S E N S OR
E R ROR 5 1 a
P O S I T I V E P . S E N S OR
E R ROR 6 1 7
S U B T A N K S N N : 1 2 3 4 5 6 7 8
E R ROR 6 1 8
T A N K l e v e l H : 1 2 3 4 5 6 7 8
E R ROR 6 1 9
T A N K l e v e l L : 1 2 3 4 5 6 7 8
E R ROR 6 1 a
O V E R F L OW : 1 2 3 4 5 6 7 8
E R ROR 6 1 b
S U P P L Y I N K : 1 2 3 4 5 6 7 8
E R ROR 6 1 c
N E G A T I V E P . CON T RO L
E R ROR 6 1 d
N E G A T I V E P . N o t E n o u g h
E R ROR 6 1 e
N E G A T I V E P . O V E R
5-20
Cause
There is a slot in which the ink bottle
has not been inserted more than a
certain time.
The media jam occurs.
The media width has not been
detected correctly.
A HDC position counter error
occurred.
Y-origin could not be detected.
Abnormal linear scale.
The value of the negative pressure
sensor is abnormal.
The value of the positive pressure
sensor is abnormal.
The liquid level sensor abnormality of
the sub tank has been detected.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor High.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor Low.
Overflow from the sub tank has been
detected.
Ink could not be supplied to the sub
tank.
Starting of the negative pressure con-
trol has an abnormality.
The negative pressure cannot be kept
properly
Solution
Set an ink bottle.
• Remove the media and reset it.
• Check the media set position. (
• Turn off the main power to the machine and
turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
• Perform "PRESSURE ADJUST" (
of the maintenance. If you cannot adjust it
to the normal value, or, even if you perform,
it may be displayed, contact your local dis-
tributor to call for service.
• Turn off the main power to the machine and
turn it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
• Perform "SUB TANK" (
maintenance. Even if you performed this,
when the message is displayed, contact
your local distributor to call for service.
• Perform "SUB TANK" (
maintenance. Also check the remaining
amount of ink in the ink bottle. Even if you
performed this, when the message is dis-
played, contact your local distributor to call
for service.
• Perform "PRESSURE ADJUST" (
of the maintenance. If you cannot adjust it
to the normal value, or, even if you perform,
it may be displayed, contact your local dis-
tributor to call for service.
P.2-24)
P.5-9)
P.5-6) of the
P.5-6) of the
P.5-9)