Table of Contents
Advertisement
Message
< L OC A L >
N E G A T I V E P R E S S U R E
< L OC A L >
P O S I T I V E P R E S S U R E
< L OC A L >
N E G A T I V E P . A D J U S T
< L OC A L >
I N K N E A R E N D
< L OC A L >
E X P I R A T I ON
< L OC A L >
E X P I R A T I ON ( 1 M )
< L OC A L >
E X P I R A T I ON ( 2 M )
< L OC A L >
S U P P L Y
I N K
: MMB B Y Y K K
< L OC A L >
S u b t a n k S e n s : MMB B Y Y K K
< L OC A L >
I n k O v e r f l o w : MMB B Y Y K K
< L OC A L >
T A N K l e v r l H
: MMB B Y Y K K
< L OC A L >
T A N K l e v r l L
: MMB B Y Y K K
< L OC A L >
R e p l a c e D e A i r M o d u l e
< L OC A L >
M a c h i n e T EMP / H i
< L OC A L >
M a c h i n e T EMP / L o
5-14
Cause
The value of the negative pressure
sensor is abnormal.
The value of the positive pressure
sensor is abnormal.
Pressure needs to be adjusted.
The ink of the ink bottle has been
nearly used up.
[ E N T ]
The specified expiration date of an ink
bottle has passed.
[ E N T ]
The expiration date of an ink bottle
has passed (one month has passed
[ E N T ]
after the specified expiration date).
The expiration date of an ink bottle
has passed (two months have passed
[ E N T ]
after the specified expiration date).
Ink could not be supplied to the sub
tank.
The liquid level sensor abnormality of
the sub tank has been detected.
Overflow from the sub tank has been
detected.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor High.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor Low.
The deaeration module in the ink path
shall be replaced soon.
(One year has passed since you
started using it.)
The machine temperature is high.
* * * ° C
The machine temperature is low.
* * * ° C
Solution
• Perform "PRESSURE ADJUST" (
of the maintenance. If you cannot adjust it
to the normal value, or, even if you perform,
it may be displayed, contact your local dis-
tributor to call for service.
• Contact your local distributor to call for ser-
vice.
• Press the
key to check the rele-
vant ink bottle. Be careful because it may
be INK NEAR END soon.
The expiration date has passed.
However, you can use it until the end of the
following month.
• One month has passed after the expiration
date.
However, you can use it until the end of this
month. (The ink bottle lamp blinks in red.)
Two months have passed after the expiration
date.
Replace the ink bottle generating the warn-
ing with a new one.
• Perform "SUB TANK" (
maintenance. Also check the remaining
amount of ink in the ink bottle. Even if you
performed this, when the message is dis-
played, contact your local distributor to call
for service.
• Turn off the power to the machine and turn
it on after a while.
• If the same error message appears again,
contact your local distributor to call for ser-
vice.
• Perform "SUB TANK" (
maintenance. Even if you performed this,
when the message is displayed, contact
your local distributor to call for service.
• The deaeration module shall be replaced.
Contact a distributor in your district, our
office, or our call center.
• Adjust the ambient temperature of the
installation place.
P.5-9)
P.5-6) of the
P.5-7) of the
Advertisement
Table of Contents
