Table of Contents
Advertisement
Message
< L OC A L >
Ym o t o r
C l e a n i n g [ MN T ]
< L OC A L >
R e p l a c e Ym o t o r
B r u s h
< L OC A L >
E . H E A T E R E R ROR
< L OC A L >
E . H E A T E R CON N E C T
< L OC A L >
T a k e - U P C o v e r O P E N
< L OC A L >
T a k e - U P L i m i t D E T E C T
< L OC A L >
T a k e - U P WRONG
< L OC A L >
F e e d i n g C o v e r O P E N
< L OC A L >
F e e d i n g L i m i t D E T E C T
< L OC A L >
F e e d i n g WRONG
M i s t
F i l t e r
P l e a s e R e p l a c e
[ E N T ]
Cause
Time to clean the Y motor has come.
Time to replace the brush of Y motor
has come.
An abnormality of the external heater
has been detected.
The external heater is not connected
correctly.
The cover of the media take-up
machine was open was detected.
The control limit sensor of the media
take-up machine was detected.
An abnormality occurred in the take-
up status of the media take-up
machine.
The cover of the media feeding
machine was open was detected.
The control limit sensor of the media
feeding machine was detected.
An abnormality occurred in the feed-
ing status of the media feeding
machine.
Time to replace the mist filter has
come.
Warning / Error Messages
Solution
• Turn off the power and vacuum debris of
the Y motor from the vacuuming window.
(
P.4-28)
• After the replacement, press the
key on the local screen to clear the warn-
ing.
• The brush of Y motor shall be replaced.
Contact a distributor in your district, our
office, or our call center.
• Contact a distributor in your district, our
office or our call center.
• When you do not use the external heater,
set the external heater to "OFF" in the
"HEATER" of the Setting Mode (
By doing this, you can perform printing.
• Check
the
connection
machine and the external heater.
• Even if you performed this, if the same error
is displayed, contact a distributor in your
district, our office or our call center.
• When you do not use the external heater,
set the external heater to "OFF" in the
"HEATER" of the Setting Mode (
By doing this, you can perform printing.
• Check the cover of the media take-up
machine. Even if you close the cover, if the
same error is displayed, contact a distribu-
tor in your district, our office or our call cen-
ter.
• Lower the position of the tension bar at the
take-up side. Even if you lower the position,
if the same message is displayed, contact a
distributor in your district, our office or our
call center.
• Check that the media is set on the media
take-up machine correctly.
• Check that the paper core for taking up
media does not run idle.
• Check the cover of the media feeding
machine. Even if you close the cover, if the
same error is displayed, contact a distribu-
tor in your district, our office or our call cen-
ter.
• Lower the position of the tension bar at the
feeding side. Even if you lower the position,
if the same message is displayed, contact a
distributor in your district, our office or our
call center.
• Check that the media is set on the media
feeding machine correctly.
• Check that the paper core of roll media
does not run idle.
• For replaceing the filter, refer to the sepa-
rate "Requests for Daily Care and Mainte-
nance".
MAINT.
1
P.3-3).
between
this
1
P.3-3).
1
1
5
5-15
Advertisement
Table of Contents
