Table of Contents
Advertisement
Minimum Time Between Rings
Default = 200 (2000 ms)
Specify the minimum amount of time allowed between valid rings
in 10 millisecond increments (100–999 x 10 ms).
Setting the Minimum Time Between Rings:
1. Once the item number has been entered, specify the minimum
time between rings (100–999).
2. Press # to apply the new setting.
Phone Access Settings
Local Phone Settings
Local phone settings allow you to choose how phones
located on the same premises as the panel interact with the
system.
Enable Local Phone Access in Partition/Area 1
Default = 0 (Off - Commercial Burg)
Default = 1 (On - Home Navigator)
This setting allows you to enable local phone control in partition/
area 1. If on, partition/area 1 may be controlled by local on pre-
mises phones.
To Turn Local Phone Access in Partition/Area 1 On/Off:
Once the item number has been entered, enter 1 to turn this setting
on, or 0 to turn it off. Press # to apply the new setting.
Local Phone Control Sequence
Default = #*
Enter up to a 4-digit DTMF (touch-tone) sequence for local phone
control. This is the sequence of numbers the user will have to
enter when accessing the panel locally (on-site). Partition/area 1
only.
Format:
q
Enter 00–09 for numbers 0-9.
q
Enter 10 for * (star).
q
Enter 11 for # (pound).
To Enter Local Phone Control Sequence:
1. Enter the item number.
2. Enter the sequence using the format above. For example, if
you wanted the sequence to be "12#*," at the keypad you
would enter "01, 02, 11, 10."
3. Press # and the touchpad displays the new sequence.
To Delete the Local Phone Control Sequence:
1. Enter the item number.
2. Enter 0 + #. The touchpad will display
Commercial Burglary and Home Navigator System
17023
Phone Device Override Sequence
Default = **##
Enter up to a 4-digit DTMF (touch-tone) sequence for phone
device override. This sequence will instruct the panel to seize the
line from the local phone and initiate a remote connection. Users
will be able to enter this sequence and bypass any phone devices
(answering machines, fax machines, etc.) when calling from a
remote phone. Partition/area 1 only.
Format:
q
q
q
To Enter Phone Device Override Sequence:
1. Enter the item number.
2. Enter the sequence using the format above. For example, if
17085
3. Press # and the touchpad displays the new sequence.
To Delete Phone Device Override Sequence:
1. Enter the item number.
2. Enter 0 + #. The touchpad will display
Time Between Phone Panic Keystrokes
Default = 2 Seconds
Specify the maximum time allowed (in seconds) between key-
strokes in a phone panic sequence. If this delay is exceeded, a
panic alarm will not be activated. Partition/area 1 only.
17056
Setting the Time Between Phone Panic Keystrokes:
1. Once the item number has been entered, enter the maximum
2. Press # to apply the new setting.
Local Phone Connect Time
Default = 5 Seconds
Specify the maximum time allowed (in seconds) between local
phone off-hook and DTMF seize sequence for local phone con-
trol. If the maximum time is exceeded, remote phone control will
be put on hold. Partition/area 1 only.
Setting the Local Phone Connect Time:
1. Once the item number has been entered, enter the maximum
2. Press # to apply the new setting.
.
NO DATA
Local Phone Answer Time
Default = 8 Seconds
Specify the maximum time (in seconds) between a ring signal and
local phone off-hook signal to be considered answer of call. Parti-
tion/area 1 only.
Setting the Local Phone Answer Time:
1. Once the item number has been entered, enter the answer time
2. Press # to apply the new setting.
Enter 00–09 for numbers 0-9.
Enter 10 for * (star).
Enter 11 for # (pound).
you wanted the sequence to be "12#*," at the keypad you
would enter "01, 02, 11, 10."
delay (1–5).
allowable connect time (0–255 [0 = no max time]).
(0–255).
Programming the Panel
17057
.
NO DATA
17030
17028
17029
29
Advertisement
Table of Contents
