Table of Contents
Advertisement
Programming the Panel
Entry Delay
Default = 32 Seconds
Enter the length of the standard entry delay (in seconds). This is
the number of seconds the user has to disarm the system after trip-
ping a standard delay zone. If the system isn't disarmed within
this time period an alarm is generated.
Setting the Entry Delay:
Once the item number has been entered, enter the number of sec-
onds (24–120) users will have to disarm the system. Press # to
apply the new setting.
Exit Delay
Default = 32 Seconds
Enter the length of the standard exit delay (in seconds). This is the
number of seconds the user has to exit the premises through a
standard delay door after arming the system. If the user trips a
zone after this time period has expired, an alarm is generated.
Setting the Exit Delay:
Once the item number has been entered, enter the number of sec-
onds (24–120) users will have to exit the premises after arming
the system. Press # to apply the new setting.
Extended Delay
Default = 2 Minutes
Enter the length of the extended delay. The extended delay time
determines how much time (in minutes) the user has to enter or
exit the premises through an extended delay door without causing
an alarm.
Setting the Extended Delay:
Once the item number has been entered, enter the number of min-
utes (1–10) for the extended delay and press #.
Exit Delay Termination
Default = 0 (Off)
If on, the system will arm as soon as it detects a delay zone clos-
ing. Once a person leaves through an exit delay door and the door
closes, the exit delay is terminated and the system is armed.
Note
Cannot be used with Exit Delay Reset setting (xx102).
To Turn Exit Delay Termination On/Off:
Once the item number has been entered, enter 1 to turn the setting
on or 0 to turn it off. Press # to apply the new setting.
22
xx003
Exit Delay Reset
Default = 0 (Off)
If on, the system will allow a one-time reset of the standard exit
delay. If a user leaves through a delay door and the door closes,
they may re-enter through the door within the exit delay time
period and the system will reset the exit delay.
Note
Cannot be used with Exit Delay Termination setting
(xx101).
To Turn Exit Delay Reset On/Off:
Once the item number has been entered, enter 1 to turn the setting
on or 0 to turn it off. Press # to apply the new setting.
xx004
Fast Beep Duration
Default = 10 Seconds
Enter the length of time (in seconds) that fast beeps will sound
during the last portion of the exit delay to signal the delay is end-
ing.
Setting the Fast Beep Duration:
Once the item number has been entered, enter the number of sec-
onds (5–15) fast beeps will sound before the end of the delay and
press #.
xx005
Exit Beeps only at end of Exit Delay
Default = 1 (On)
If on, only the fast beeps at the end of the exit delay will sound. If
off, slow exit delay beeps will sound followed by the fast beeps at
the end of the delay.
To Turn Exit Delay Beeps On/Off:
Once the item number has been entered, enter 1 to turn the setting
on or 0 to turn it off. Press # to apply the new setting.
xx101
Entry Delay Beeps
Default = 0 (Off)
If on, beeps only sound during the standard entry delay. If off,
beeps sound during all segments of an entry delay including stan-
dard, extended, and twice extended.
To Turn Entry Delay Beeps On/Off:
Once the item number has been entered, enter 1 to turn the setting
on or 0 to turn it off. Press # to apply the new setting.
Zone Settings
Chime Text
Default = 0 (Off)
If on, zone text will be announced over speakers and displayed on
touchpads whenever a chime sounds (the sensor is open or
closed). See Table B1 on page 79 for the zone types that chime.
Note
Only partition/area 1 has voice capabilities.
To Turn Chime Text Setting On/Off:
Once the item number has been entered, enter 1 to turn the setting
on or 0 to turn it off. Press # to apply the new setting.
Commercial Burglary and Home Navigator System
xx102
xx006
xx100
xx103
xx110
Advertisement
Table of Contents
