Table of Contents
Advertisement
Programming the Panel
On Hook Hang Up Time
Default = 4 Seconds
Select the amount of time (in seconds) a local telephone must be
on-hook before hanging up. Partition/area 1 only.
Setting the On Hook Hang Up Time:
1. Once the item number has been entered, enter the hang up
time (2–10).
2. Press # to apply the new setting.
Phone Police Panic Enable
Phone Aux/Med Panic Enable
Phone Fire Panic Enable
Defaults = 0 (Off)
Select whether or not you want to enable the selected phone panic
sequence. If on, users will be able to activate the specific panic
alarm using a local phone (88888 for police, 77777 for auxiliary/
medical, and 99999 for fire). Partition/area 1 only.
To Turn Phone Panic On/Off:
Once the desired item number has been entered, enter 1 to turn
this setting on, or 0 to turn it off. Press # to apply the new setting.
Remote Phone Settings
Remote phone settings allow you to choose how phones
located off premises (different line) interact with the panel.
Enable Remote Phone Access
Default = 1 (On)
Note
Turning this setting to "off" will prevent the panel from
receiving future downloader calls.
This setting allows you to enable remote phone access. If on, the
panel may be controlled using remote off-site phones. Partition/
area 1 only.
Note
For residential use only.
To Turn Remote Phone Access On/Off:
1. Once the item number has been entered, enter 1 to turn this
setting on (enabled), or 0 to turn it off.
2. Press # to apply the new setting.
Enable Remote Phone Ring Count
Default = 1 (On)
This setting allows you to tell the panel to count remote phone
rings so that it will pick up after a certain number of rings. This
setting only works if Remote Phone Access setting (above) is set
to "on". Partition/area 1 only.
For residential use only.
To Turn Remote Phone Ring Count On/Off:
1. Once the item number has been entered, enter 1 to turn this
setting on, or 0 to turn it off.
2. Press # to apply the new setting.
30
17027
Answer Phone after XX Rings
Default = 12 Rings
Specify the number of rings after which the panel will answer an
incoming phone call. The Remote Phone Ring Count (17087) set-
ting must be set to "on" for this setting to work. Partition/area 1
only.
Note
For residential use only.
To Set the Number of Rings:
1. Once the item number has been entered, specify the maximum
number of rings (1–12).
17080
2. Press # to apply the new setting.
17081
17082
Enable Toll Saver
Default = 1 (On)
Choose whether or not to enable the panel to answer a remote
phone up to 4-rings earlier than normal if an alarm condition or
system trouble has occurred. Normal is considered the value in
Answer Phone After XX Rings setting (17052). The Remote Phone
Ring Count setting (17087) must be set to "on" for this setting to
take effect. Partition/area 1 only.
Note
For residential use only.
To Turn Toll Saver On/Off:
1. Once the item number has been entered, enter 1 to turn this
setting on, or 0 to turn it off.
17086
2. Press # to apply the new setting.
Enable Remote Phone Ring-Pause-Ring
Default = 1 (On)
This setting allows you to program the panel to answer remote
phone ring-pause-rings. When on, a user can call the panel once,
hang up, and call again. The panel will then answer the phone.
Use this setting if an answering machine shares a phone line with
the panel. Partition/area 1 only.
Note
The user must not exceed the number of rings in the
Cancel Ring Pause Ring after XX Rings setting (17053)
when calling the panel. Additionally, the user must call
the panel again between the times programmed in set-
tings 17025 and 17026.
For residential use only.
17087
To Turn Remote Phone Ring-Pause-Ring On/Off:
Once the item number has been entered, enter 1 to turn this setting
on, or 0 to turn it off. Press # to apply the new setting.
Min Time Between Ring-Pause-Ring Calls
Default = 10 Seconds
Specify the minimum time (in seconds) between ring-pause-ring
calls. This is the minimum amount of time that must elapse before
the second call in a ring-pause-ring attempt. Partition/area 1 only.
Setting the Minimum Time Between Ring-Pause-Ring Calls:
1. Once the item number has been entered, specify the minimum
time (6–20).
2. Press # to apply the new setting.
Commercial Burglary and Home Navigator System
17052
17090
17088
17025
Advertisement
Table of Contents
