Table of Contents
Advertisement
Output Configuration
Default = NA
Use the procedure below for mapping outputs.
To Program an Output:
1. Once in program mode enter 50005. The display shows
OUTPUT NUMBER OR PRESS
2. Enter the desired 3-digit output number from the following
choices:
q 001 - 100, programmable outputs.
q 501–504/508, Interior siren outputs (1 per partition/
area).
q 601–604/608, Exterior siren outputs (1 per partition/
area).
q 701–704/708, Strobe outputs (1 per partition/area).
3. Press #. The display shows
#
.
OR PRESS
TO ACCEPT
4. Enter the output type from the following choices:
q Enter 1 for a Bus Module Output.
q Enter 3 for a SnapCard Output.
q Enter 4 for an Panel Output.
5. Press #. The display shows
n
#
OUTPUT DATA
OR PRESS
6. Based on the output type, enter the required data from the
choices below.
Bus Module Output
Enter the 8-digit device ID and press #.
Enter 1 + # Á for output data 4. Output data 5 shows
00000000. The first 4 places represent outputs 1-4 on a 4
Relay Output Module.
Choose which output(s) to activate. For example, entering
10010000 activates outputs 1 and 4 on a 4 Relay Output
Module.
SnapCard Output
Output data 5 shows 00000000. The first 4 places represent
an output SnapCard mounted in the lower slot (SnapCard 1).
The last 4 places represent an output SnapCard mounted in
the side slot (SnapCard 2).
Choose which output(s) to activate. For example, entering
01000010 would activate the second output on SnapCard 1,
and the third output on SnapCard 2.
Panel Output
Output data 5 shows 00000000. The first 6 places represent
general purpose outputs 1–6, 7 represents the panel interior
siren output, and 8 represents the panel exterior siren output.
Choose which output(s) to activate. For example, entering
11000000 activates onboard outputs 1 and 2.
Commercial Burglary and Home Navigator System
50005
*
.
TO CANCEL
n.
OUTPUT TYPE IS
ENTER NEW TYPE
n
nnnnnnnn.
OUTPUT DATA
IS
.
TO ACCEPT
Menu Output Text
Default = None
Use the following guidelines to "name" the X-10 and non-X-10
menu output numbers that appear in the "Lights/Devices" user
menus.
q
Use the item numbers that appear in Table B2 on page 85 for
ENTER
characters and words listed there.
q
If a desired word does not appear in Table B2, create it using
the characters (custom text).
Note
Only preprogrammed words from Table B2 can be spo-
ken by the panel. Silence takes the place of any created
words when the panel voice speaks. However, created
words are displayed just like preprogrammed words.
q
When using words from Table B2, spaces between them
appear automatically. When using characters from Table B2
to create words, you must reserve an item number for a
'space' after the word.
q
Each character or word uses up one item number. For exam-
ple, a word from the list counts as one item number. A cre-
ated word (such as BOY'S) counts as six item numbers—4
letters, 1 apostrophe, and 1 space.
q
Only 8 item numbers are allowed for each output name, so
ENTER
plan ahead before programming output text. You may need
to abbreviate words to avoid running out of item numbers.
To Program Output Text:
1. Once in program mode enter 49003. The display shows
OUTPUT NUMBER OR PRESS
2. Enter the desired output number as follows:
q Partition 1—1 thru 40
q Partition 2—41 thru 80
q Partition 3—81 thru 120
q Partition 4—121 thru 160
q Partition 5—161 thru 200
q Partition 6—201 thru 240
q Partition 7—241 thru 280
q Partition 8—281 thru 320
Note
Entering an output number outside the range for a given
partition is indicated by an "Invalid" message.
3. Press #. The display shows
.
TEXT
ENTER TEXT NUMBERS OR PRESS
4. Enter the numbers of the desired characters or words. If you
make a mistake press * to start over.
5. Once all numbers have been entered, press # to accept. The
display shows the new output text.
To Delete Output Text:
1. Once in program mode enter 49003. The display shows
OUTPUT NUMBER OR PRESS
2. Enter the desired output number and press #. The display
shows
TEXT FOR OUTPUT
NUMBERS OR PRESS
3. Enter 000 and press #. The display shows
.
IS NO TEXT
Programming the Panel
*
.
TO CANCEL
nn
TEXT FOR OUTPUT
IS CURRENT
#
.
TO ACCEPT
*
.
TO CANCEL
nn
.
IS CURRENT TEXT
ENTER TEXT
#
.
TO ACCEPT
TEXT FOR OUTPUT
49003
ENTER
ENTER
nn
37
Advertisement
Table of Contents
