Table of Contents
Advertisement
Partition/Area Text
Default = None
Use the following guidelines to assign each partition/area a name.
q
Use the item numbers that appear in Table B2 on page 85 for
characters and words listed there.
q
If a desired word does not appear in Table B2, create it using
the characters (custom text).
q
When using words from Table B2, spaces between them
appear automatically. When using characters from Table B2
to create words, you must reserve an item number for a
'space' after the word.
q
Each character or word uses up one item number. For exam-
ple, a word from the list counts as one item number. A cre-
ated word (such as BOY'S) counts as six item numbers—4
letters, 1 apostrophe, and 1 space.
q
Only 8 item numbers are allowed for each partition/area
name, so plan ahead before programming partition/area text.
You may need to abbreviate words to avoid running out of
item numbers.
To Program Partition/Area Text:
1. Once in program mode enter 49004. The display shows
PARTITION NUMBER OR PRESS
2. Enter the desired partition number and press #. The display
shows
TEXT FOR PARTITION N IS CURRENT TEXT
#
NUMBERS OR PRESS
TO ACCEPT
3. Enter the numbers of the desired characters or words. If you
make a mistake press * to start over.
4. Once all numbers have been entered, press # to accept. The
display shows the new partition/area text.
To Delete Partition/Area Text:
1. Once in program mode enter 49004. The display shows
PARTITION NUMBER OR PRESS
2. Enter the desired partition/area number and press #. The dis-
play shows
TEXT FOR PARTITION N IS CURRENT TEXT
#
NUMBERS OR PRESS
TO ACCEPT
3. Enter 000 and press #. The display shows
.
IS NO TEXT
Alarm Settings
LTime
Default = 12:00
This is the time of day when the system will annunciate any exist-
ing trouble conditions. For Advent Commercial Burglary panels,
trouble(s) are annunciated every 4 hours. If the LTIME is set at
12:00 pm then the system will announce trouble(s) at 12:00 pm,
4:00 pm, 8:00 pm, 12:00 am, 4:00 am, and 8:00 am.
For Advent Home Navigator panels, trouble(s) are annuciated
every 24 hours (at LTIME).
To Set the LTIME Sound Time:
Once the item number has been entered, enter the 4-digit time
(00:00–23:59) in 24 hour format and press #.
Note
The Enable Daily Reporting of Partition/Area Trouble
setting (xx108) must be set to "on" for this setting to
work.
Commercial Burglary and Home Navigator System
49004
ENTER
*
.
TO CANCEL
.
ENTER TEXT
.
ENTER
*
.
TO CANCEL
.
ENTER TEXT
.
TEXT FOR PARTITION
xx001
Local Trouble Annunciation at LTime
Default = 1 (On)
Enables annunciation of all trouble conditions at LTime.
To set the Local Trouble Annunciation at LTIME:
Once the item number has been entered, enter 1 for on, or 0 for
off. Press # to apply the new setting.
Siren Sound Time
Default = 16 Minutes (Commercial Burg)
Default = 8 Minutes (Home Navigator)
This is the number of minutes that the alarm siren is allowed to
sound. The siren will silence when this value is reached.
To Set Siren Sound Time:
Once the item number has been entered, enter the number of min-
utes (01–30) you wish the siren to sound and press #.
Exterior Siren Sounds Instantly
Default = 0 (Off)
This setting allows you to set the delay (in seconds) before an
exterior siren sounds during and alarm. This includes all high
level alarms, except for auxiliary alarms, which don't sound exte-
rior sirens. If set to on, exterior sirens sound instantly. If set to off,
exterior sirens sound after a 15-second delay.
Turning Exterior Siren Delay On/Off:
Once the item number has been entered, enter 1 for on (15-second
delay), or 0 for off (no delay). Press # to apply the new setting.
n
Zone Tamper Alarm Enable
Default = 0 (Off)
This setting determines whether a tamper alarm is generated for a
zone that is not armed (applies to non-fire zones only). If on, a
zone tamper alarm is generated when a zone tamper is detected in
any arming level. If off, an alarm is only generated when the zone
is in an active level.
Turning Zone Tamper Report Enable On/Off:
Once the item number has been entered, enter 1 for on (alarm in
all levels), or 0 for off (alarm in active levels). Press # to apply the
new setting.
Fire Tamper Response
Default = 0 (Off)
This setting enables the panel to generate a tamper alarm (in addi-
tion to a trouble report) when tampering of a fire zone is detected.
Setting Fire Tamper Response to On/Off:
Once the item number has been entered, enter 1 for on (alarm is
generated) or 0 for off (alarm not generated). Press # to apply the
new setting.
Programming the Panel
xx108
xx002
xx113
xx079
xx083
17
Advertisement
Table of Contents
