Lenovo TD200 - ThinkServer - 3809 Hardware Maintenance Manual page 227

– Slot 2, PCI Express Gen 2 x16 (x8)
– Slot 3, PCI Express Gen 2 x8 (x4)
– Slot 4, PCI Express Gen 2 x8 (x4)
– Slot 5, PCI Express Gen 2 x8 (x8)
– Slot 6, PCI 32-bit/33 MHz
– If you install the one-slot PCI extender card in the server:
– One additional PCI Express Gen 1 x8 (x4) slot is available
– If you install the two-slot PCI extender card in the server:
• You can install full-length adapters that are supported in slots 2, 3, 4, and 5 on the system board, and the
slots on the one-slot or two-slot extender cards. You can only install half-length adapters in slots 1 and 6.
• The 32-bit slot 6 supports 5.0 V keyed PCI adapters; they do not support 3.3 V keyed adapters. Universal
adapters are supported in slots 4 and 5 if they are universally keyed.
• You can install the ServeRAID-BR10i SAS/SATA controller, the optional ServeRAID-MR10i SAS/SATA
controller, or the optional ServeRAID-MR10is VAULT SAS/SATA controller in slots 1 of hot-swap SAS or
hot-swap SATA models. These ServeRAID adapters are not supported on the simple-swap models.
• The ServeRAID-BR10i adapter comes standard on hot-swap SAS and hot-swap SATA models and
provides RAID levels 0, 1, and 1E support. You can order the ServeRAID-MR10i adapter which provides
RAID levels 0, 1, 5, 6, 10, 50, and 60 support, and the optional ServeRAID-MR10is adapter with an
encryption 1078 DE chip provides RAID levels 0, 1, 5, 6, 10, 50, and 60 support. To ensure that any of
your ServeRAID 10i, 10is, or 10M adapters function properly on UEFI-based servers, make sure that the
adapter firmware level is updated to at least 11.x.x-XXX , and the supporting drivers.
Attention: Some cluster solutions require specific code levels or coordinated code updates. If the
device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution
before you update the code.
• The server scans PCI Express slot 1 and PCI-Express slots 2 and 3 to assign system resources. Then, the
server starts the devices in the following order, if you have not changed the default startup sequence: PCI
Express slot 1, PCI Express slot 2, PCI slot 6, and PCI Express slot 3.
• For a list of supported options for the server, see http://www.lenovo.com/thinkserver.
To install an adapter, complete the following steps:
Note: The instructions in this section apply to any PCI adapter (for example, video graphics adapters
or network adapters).
1. Read the safety information (see Chapter 2 "Safety information" on page 3).
2. Turn off the server and peripheral devices and disconnect all external cables and power cords; then,
remove the side cover. See "Removing the side cover" on page 146.
3. Carefully lay the server on its side so that it is lying flat and facing up.
Note: Do not allow the server to fall over.
4. Follow the cabling instructions that come with the adapter to set jumpers or switches, if there are any.
Route the adapter cables before you install the adapter.
5. Rotate the rear adapter-retention bracket to the open (unlocked) position.
6. If you are installing a full-length adapter, press on the release lever on the right side of the front
adapter-retention bracket to release the retaining tab on the left side of the bracket.
.
Chapter 7 Installing and replacing FRUs
219