Western Digital ActiveScale X100 Installation Manual page 102

ActiveScale™ X100 Installation Guide
c. Run the following commands:
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1)
(SiteN_System_Interconnect1) #write memory confirm
Config file 'startup-config' created successfully. Configuration Saved!
(SiteN_System_Interconnect1)
0/49ScaleoutNetwork_InterconnectUp40G
(Site1_Storage_Interconnect1) (Config)#show interfaces status all | include 0/51
0/51ScaleoutNetwork_InterconnectUp40G
(SiteN_System_Interconnect1) (Config)#exit
2. Create an alias on your laptop to System Interconnect 2 on the existing system:
Note: Change the IP address in the first alias to match your network settings, but
do not change the link-local IP address in the second alias.
sudo ifconfig eth1:0 172.16.210.240 up #this IP address should match your setup
sudo ifconfig eth1:1 169.254.210.240 up
3. Connect to System Interconnect 2 (username:
lab@mw-<System IP>:$ telnet <IP of System Interconnect 2> Trying
Connected to 172.16.210.200. Escape character is '^]'. User:admin
Password:
4. Run the following commands:
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2)
(SiteN_System_Interconnect2) #write memory confirm
Config file 'startup-config' created successfully. Configuration Saved!
(SiteN_System_Interconnect2) #show
0/49ScaleoutNetwork_InterconnectUp40G
(SiteN_System_Interconnect2) #show
0/51ScaleoutNetwork_InterconnectUp40G
(SiteN_System_Interconnect2) #quit
Connection closed by foreign host.
5. Reconfigure the System Interconnects on the new systems:
a. Connect an Ethernet cable from your laptop to port 44 on System Interconnect 1 of the new system.
b. Create an alias on your laptop to System Interconnect 1 on the new system:
Note: Do not change the link-local IP address in the command below.
sudo ifconfig eth1:0
c. Connect to System Interconnect 1 (username:
lab@mw-<System IP>:~$ telnet <System Interconnect 1 IP> Trying
>en
#conf
(Config)#interface 0/49
(Interface 0/49)#no shutdown
(Interface 0/49)#exit
(Config)#interface 0/51
(Interface 0/51)#no shutdown
(Interface 0/51)#exit
(Config)#exit
(Config)#show
Full40G
FullUnknown Inactive
admin
>en
#conf
(Config)#interface 0/49
(Interface 0/49)#no shutdown
(Interface 0/49)#exit
(Config)#interface 0/51
(Interface 0/51)#no shutdown
(Interface 0/51)#exit
(Config)#exit
interfaces
Full40G
interfaces
FullUnknown Inactive
<ip_address> up
admin
102
interfaces status all | include
FullUnknown Active
, no password):
status all | include
FullUnknown Active
status all | include
, no password):
0/49
172.16.210.200...
0/49
0/51