Mitsubishi MELSEC-L series Programming Manual page 384

[A]
ABRST (absolute position restoration)................ 5-233
Analog instruction.................................... 2-3,2-11,2-12
Analog module ........................................................ 1-7
[B]
BIDIN (receiving data using bidirectional protocol
communication)..................................................... 5-73
BIDOUT (sending data using bidirectional protocol
communication)..................................................... 5-70
BUFRCV (receiving data in fixed buffer
communication)................................................... 5-202
BUFRCVS (receiving data with interrupt program)
.................................................................... 5-79,5-206
BUFSND (sending data in fixed buffer communication)
............................................................................ 5-208
[C]
CC-Link IE controller network instruction ................ 2-6
CC-Link IE controller network module..................... 1-7
CC-Link instruction.................................................. 2-5
CC-Link system master/local module...................... 1-7
CLOSE (connection closing) ............................... 5-199
Configuration of Instructions ................................... 3-2
CSET (initial setting) ............................................. 5-85
CSET (programmable controller CPU monitoring)
.............................................................................. 5-89
CSET (receive data clear)..................................... 5-76
[D]
Destination .............................................................. 3-3
[E]
ERRCLR (clearing error information) .................. 5-212
ERRRD (reading error information)..................... 5-215
Ethernet instruction ................................................. 2-6
Ethernet interface module ....................................... 1-7
[G]
GETE (user frame reading)................................. 5-100
[H]
HOW TO READ INSTRUCTIONS .......................... 4-1
[I]
I/O number .............................................................. 3-2
I/O number of module ............................................. 3-2
ICCNTRD (current value read).............................. 8-18
ICCOVWR (coincidence output point write) .......... 8-24
ICFCNT (frequency measurement)....................... 8-25
ICLTHRD (latch counter value read)..................... 8-22
ICPLSRD (pulse measurement read) ................... 8-27
ICPREWR (preset value write).............................. 8-21
ICPWM (PWM output)........................................... 8-28
Index - 2
ICRCNT (rotation speed measurement)................ 8-26
ICRNGWR (ring counter upper/lower limit value write)
.............................................................................. 8-19
ICSMPRD (sampling counter value read) ............. 8-23
INPUT (receiving data using nonprocedural protocol
communication) ..................................................... 5-67
INSTRUCTION TABLES ......................................... 2-1
IPABRST (absolute position restoration)............... 8-11
IPDSTRT (positioning start) .................................... 8-3
IPJOG (JOG start)................................................... 8-9
IPOPR (OPR start) .................................................. 8-7
IPPSTRT (tabel start) .............................................. 8-2
IPSIMUL (2 axes simultaneous start)...................... 8-6
IPSPCHG (speed change) .................................... 8-14
IPSTOP (axis stop)................................................ 8-13
IPTPCHG (target position change)........................ 8-16
[L]
LOGTRG (trigger logging set) ................................. 9-2
LOGTRGR (trigger logging reset) ........................... 9-2
[M]
MELSECNET/H instruction ..................................... 2-6
MELSECNET/H network module ............................ 1-7
Modem interface instruction .................................... 2-4
Modem interface module......................................... 1-7
Modules and Versions Applicable to Instructions.... 1-7
MRECV (receiving e-mail)................................... 5-221
MSEND (sending e-mail)..................................... 5-226
[N]
Network number ...................................................... 3-2
[O]
OFFGAN (mode switching) ..................................... 5-2
OGLOAD (reading offset/gain setting value)........... 5-4
OGSTOR (restoring offset/gain setting value)....... 5-31
ONDEMAND (sending data using the on-demand
function)................................................................. 5-60
OPEN (connection opening)................................ 5-195
OUTPUT (sending data using nonprocedural protocol
communication) ..................................................... 5-64
[P]
PFWRT (writing data to flash ROM).................... 5-242
PID control instruction ............................................. 2-9
PIDCONT (PID operation)............................... 6-7,6-21
PIDINIT (setting data to be used for PID operation)
........................................................................ 6-2,6-16
PIDPRMW (changing parameter for PID operation)
...................................................................... 6-12,6-27
PIDRUN (PID operation start) ....................... 6-11,6-26
PIDSTOP (PID operation stop) ..................... 6-11,6-26