Icom IC-7851 Instruction Manual page 219

15
SET MODE
■ ACC set screen (continued)
USB IF Output Level
Sets the [USB B] output level.
• Range: 0%–100% (in 1% steps)
LAN Output Select
Selects the signal output from [LAN].
• AF: AF signal is output from [LAN].
• IF: IF signal is output from [LAN].
LAN AF SQL
Select the squelch behavior of [LAN].
• OFF(OPEN): The squelch is always opened regard-
less of the transceiver's squelch con-
dition.
• ON: The squelch opens and closes, ac-
cording to the transceiver's squelch
condition.
ACC-A MOD Level
Sets the modulation input level of [A ACC1].
• Range: 0%–100% (in 1% steps)
• Approximately 200 mV at the 50% (default) setting.
ACC-B MOD Level
Sets the modulation input level of [B ACC1].
• Range: 0%–100% (in 1% steps)
• Approximately 200 mV at the 50% (default) setting.
S/PDIF MOD Level
Sets the modulation input level of [S/P DIF].
• Range: 0%–100% (in 1% steps)
USB MOD Level
Sets the modulation input level of [USB].
• Range: 0%–100% (in 1% steps)
LAN MOD Level
Sets the modulation input level of [LAN].
• Range: 0%–100% (in 1% steps)
(Default: 50%)
(Default: AF)
(Default: OFF(OPEN))
(Default: 50%)
(Default: 50%)
(Default: 50%)
(Default: 50%)
(Default: 50%)
DATA OFF MOD
Selects the connector(s) to input the modulation signal
when the data mode is OFF.
• MIC:
• ACC-A:
• ACC-B:
• MIC,ACC-A:
• MIC,ACC-B:
• ACC-A,ACC–B:
• MIC,ACC-A,ACC–B: Use the signal from [MIC], [A
• USB:
• S/P DIF:
• LAN:
DATA1 MOD
Selects the connector(s) to input the modulation signal
when the data 1 mode (D1) is ON.
• MIC:
• ACC-A:
• ACC-B:
• MIC,ACC-A:
• MIC,ACC-B:
• ACC-A,ACC–B:
• MIC,ACC-A,ACC–B: Use the signal from [MIC], [A
• USB:
• S/P DIF:
• LAN:
DATA2 MOD
Selects the connector(s) to input the modulation signal
when data 2 mode (D2) is ON.
• MIC:
• ACC-A:
• ACC-B:
• MIC,ACC-A:
15-8
(Default:
MIC,ACC-A,ACC-B
Use the signal from [MIC].
Use the signal from [A ACC1]
(pin 4).
Use the signal from [B ACC1]
(pin 4).
Use the signal from [MIC] and
[A ACC1] (pin 4).
Use the signal from [MIC] and
[B ACC1] (pin 4).
Use the signal from [A ACC1]
and [B ACC1] (pin 4).
ACC1] and [B ACC1] (pin 4).
Use the signal from [USB].
Use the signal from [S/P DIF].
Use the signal from [LAN].
(Default: ACC-A)
Use the signal from [MIC].
Use the signal from [A ACC1]
(pin 4).
Use the signal from [B ACC1]
(pin 4).
Use the signal from [MIC] and
[A ACC1] (pin 4).
Use the signal from [MIC] and
[B ACC1] (pin 4).
Use the signal from [A ACC1]
and [B ACC1] (pin 4).
ACC1] and [B ACC1] (pin 4).
Use the signal from [USB].
Use the signal from [S/P DIF].
Use the signal from [LAN].
(Default: ACC-B)
Use the signal from [MIC].
Use the signal from [A ACC1]
(pin 4).
Use the signal from [B ACC1]
(pin 4).
Use the signal from [MIC] and
[A ACC1] (pin 4).
)