Engine Lubrication - MOTO GUZZI V1000 G5 Workshop Manual
Hide thumbs
Also See for V1000 G5:
- Owner's manual (35 pages) ,
- Owner's manual (59 pages) ,
- Workshop manual (154 pages)
Table of Contents
Advertisement
82L-____________________________
--"
82
/
1L-____________________________ --"
60
m
ENGINE LUBRICATION
The
oil sump ("C.,
in
fig.
82/
3) acts
as
an
oil
tank
an
d
contains
3
liters of
oil (abt.
3/4
US gls.).
Lubrication
is by pressure. Delivery
by spur
gear
pump.
recovery by
gravity.
The pump is gear driven
directly
by
the
camshaft
and
includes:
a wire gauze
filler,
a
cartridge
filter, an oil
pressure
relief
valve,
and the
dra
in
plug
.
14.1.
OIL DELIVER PUMP
It is
of spur
gear
type.
The gear driving
shaft is
car-
ried by two rolter
beari ngs
housed
In
the oil
pump
·
body.
Inspec
tions
and
controls
(see
fig.
82.£2/
1
4
82/
2)
In
case of improper operation of the of! pump,
check
accurately
the following
:
•
Depth
of
gears.
Should be 13.973-14.000 mm
(.551-
.551").
•
Gear
housing
in
pump
body.
Should
be 14.032-
14.075
mm
(.5524-.5541'').
If
not within the
above sizes,
the
parts shou ld
be
replaced.
It
is also important
to
check that
the
%
of
the
gears does
not exceed 26.250-26.290
mm
(1.0333-
1.0377")
and
that
of
the pump housings in
the body
is no more than 26.340-26.390 mm (1.0369-1.0389")
.
Also
the 0
10
of
the
rolier
bearing
race
(Durkopp
Naf 10
x
22 x 20) should
be
within 21.989-22.002 mm
(.8657-.8662") and
housing 0
10
in
the pump
body
should be within 21.972-21.993
mm
(.8649-.8659").
Check
also
the
I/O
of the
rolier
bea ring
rac
e (Dur-
kopp
Naf 10
x
22
x
20) which should be
9.990-10.002
mm
(.3932-.3937").
If
not
within the above sizes, the parts should be
replaced.
Back
lashes
•
Between pump
gear
shaft
(9.985-10.000
mm
=
.3930-.3937") and the housing in the
pump
body
(10.013-1O.035
mm
=
.3943-.3950")
should be 0.013-
0.050 mm
(.00051-.0019").
•
Between
outer
roller bearing
race
(21.989-22.002
mm
"" .8657-.8662")
and housing
in
pump body
(21.972-
21.989
mm
-.8649-.8656") should be
from
a
clearance
of 0.004 mm (.00015") to a
negative
allowance
of
0 .030
mm
(.ooll").
•
Between
110
of roller inner race
(9.990-10.002
mm
=
.3932-.39371
")
and pump shaft
(9.085-10.000
mm
=
.3930-.3937")
should be from a clearance
of
0.017
mm
(.00066") to an
interference
of 0.010 mm
(.00039")
.
•
Between gears on
pump
shaft
(26.250-26.290
mm
=
1.0333-1.0350") and the pump body housings
(26.340-26.390 mm
=
1.0369-1.0389") should
be
0.050-
0.140
mm
=
.0019-.0055").
Hide quick links:
Advertisement
Table of Contents
