Checking With Loopback Address; Checking With Local Host Address; Checking The Images/Operations; Checking Image Operation - Canon imageRUNNERC1022 Service Manual

Chapter 2
b. TCP/IP setting of the machine is faulty
c. There is a fault in the main controller PCB, or in the installation of the PCB
d. User network is faulty

2.3.5 Checking with Loopback Address

imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
NOTE:
Because the loopback address is returned just before the main controller
PCB, you can check whether the TCP/IP setting of the machine is successful
or failed by executing Ping with this loopback address.
1) Enter the loopback address (127.0.0.1) to Ping.
- In the case of 'NG', check the TCP/IP setting of the machine again, and
then execute Ping again.
- In the case of 'OK', go through the following check for local host
address.

2.3.6 Checking with Local Host Address

imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
NOTE:
Local host address is the IP address of the machine. Thus, you can check
whether the PCB is working or faulty by executing Ping with this local host
address since the reply is returned from the main controller PCB.
1) Enter the IP address of the machine to Ping.
- In the case of 'NG', check and perform the following to execute Ping
again.
a. Faulty IP address of the machine:
Check the IP address setting of the machine again/Check with the
system administrator that the allocated IP address is valid
b. Connection failure of the main controller PCB:
Check the connection of the main controller PCB connector
c. Faulty main controller PCB:
Replace the main controller PCB
- In the case of 'OK', the user's network environment can be the problem,
so inform the status to the system administrator and ask for a measure.

2.4 Checking the Images/Operations

2.4.1 Checking Image Operation

imageRUNNER C1022 / imageRUNNER C1022i
1) Place a test chart on the copyboard glass, make a copy from each pickup
inlet and check the followings.
- Check that there is no abnormal noise generated.
- Check the image quality in each magnification.
- Check that the number of sheet set is properly applied.
2) Specify the additional function mode items (date, time etc.) when required
by users.
3) Specify the mechanical specification settings related to users when re-
quired by users.
- Enter the Service mode.(Main Menu > 2 > 8 > Main Menu)
- COPIER > OPTION > USER
4) If changing a setting in service mode, turn OFF/ON the main power
switch.

2.5 Installing the Card Reader

2.5.1 Notice At Installation

imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
C1030 / Color imageRUNNER C1030iF
CAUTION:
Installation of this equipment needs 'Card Reader Attachment Kit-F1'.

2.5.2 Checking the Contents

imageRUNNER C1022 / imageRUNNER C1022i / Color imageRUNNER
2-8
C1030 / Color imageRUNNER C1030iF
< Card Reader-E1 >
[1]
0019-0685
0019-0687
[1] Card Reader
[2]* Screw (TP; M3X12)
[3]* Toothed washer
[4]* IP-card reader cable
* Not used for this equipment.
< Copy Card Reader-F1 >
[1]
0019-0697
[1] Card Reader
[2]* Screw (RS tight; M4X10)
[3]* Toothed washer
* Not used for this equipment.
< Card Reader Attachment Kit-F1 >
0019-8625
0019-8626
[2] [3]
[4]
F-2-18
1pc
1pc
1pc
1pc
[2] [3]
F-2-19
1pc
1pc
1pc