Canon imageRUNNERC1022 Service Manual page 446

Chapter 18
No.
39 Switching of the default of LDAP detailed search condition
40 eLA card touch sound
41 PS mode 1 (8bit)
42 PS mode 2 (8bit)
57 Setting of paper size group
Secondary Battery charging completion wait timer (Unit: minute)
60
When the value is 0, it is 120 minutes.
Pulse trickle charge set timmer (Unit: second)
61
When the value is 0, it is 300 minutes.
62 Engine adjustment timer (Unit: second)
63 Engine adjustment timer (Unit: minute)
64 Engine adjustment timer (Unit: hour)
Sub item
FAX-SW
FAX-NUM
NET-SW
NETNUM
NET-CERT VERSION
SRLNUM
SIGALG
ISSUER
VLD_FROM
VLD_TO
SUBJECT
PUB_KEY
THMB_PRT
CDC-SW
CDC-NUM
EXC-NAVI
DSP-PPRSE
SET-PPRSZ
DSP-TNROW
18-30
COPIER > FUNCTION > PARAM > SYS-NUM
Function
COPIER > FUNCTION > PARAM
Not used
Not used
SW01 to SW50
001 to 050
CA certificate version
Serial number
Signature algorithm
Issuer
Commencement date of the expiration period
Finishing date of the expiration period
Subject of issuance
Public key algorithm and size
Digest (Thumb imprint)
Not used
Not used
Switch for whether or not to start up the installation navigation
When setting this switch to 1 after the installation navigation is completed, the installation navigation does not start up at the time
of next activation.
Setting value: 0: Start up the navigation. 1: Do not start up the navigation.
[Factory setting value/Value after RAM clearing: 0]
Setting of whether or not to display the paper setting screen when ACS setting is set to ON at the time of copy operation
Setting value: 0: Do not display the screen. 1: Display the screen.
[Factory setting value/Value after RAM clearing: 0]
Setting of the ACS document size when DSP-PPRSEL is set to ON
When the document size is unknown, a screen prompting an operator to enter the document size is displayed.
When the sizes other than UNKNOWN are specified, ACS judgment processing is performed based on the specified document
size.
Setting range: 0 to 20
Setting value: 0: UNKNOWN, 2: A4, 3: A5, 7: B5, 12: LGL, 13: LTR, 60: STMT
[Factory setting value/Value after RAM clearing: 0]
Setting of whether or not to display "Toner Low"
Setting value: 0: Do not display the screen. 1: Display the screen.
[Factory setting value/Value after RAM clearing: 1]
Available setting range
0:contains
1:does not contain
2:equals
3:differs from
4:begins with*
5:ends with
0:OFF,1:ON(default)
0 - 60(default:0)
0 - 60(default:0)
Setting values and groups are as
follow:
1: AB configuration
(PAPER_SIZE_GROUP_AB)
2: A configuration
(PAPER_SIZE_GROUP_A)
3: INCH configuration
(PAPER_SIZE_GROUP_INCH)
4: AB/INCH configuration
(PAPER_SIZE_GROUP_AB_INCH)
Timing to be initialized is as follow:
- CLEAR > ALL
- CLEAR > TYPE
- CLEAR > SERVICE DATA
- CLEAR -> TEL&USER DATA
(because of synchronizing the values
of ATT_ID and SYSTEM NUMERIC)
- When starting/ending the process
- Select country at startup
0-9999
0-9999
0-9999
0-9999
0-9999
T-18-41
Description
Default
0
0
0
0
0
(When the values of
SYS-NUM 62, 63, and
64 are 0, default is 2.)