Comtech EF Data SLM-7650 Installation And Operation Manual page 183

SLM-7650 Satellite Modem
Remote Control Specifications
Bulk Consol.
Status
(continued)
Parameter
Number
71
72
73
(Note 5)
74
(Note 5)
75
(Note 5)
76
(Note 5)
77
(Note 6)
78
(Note 6)
79
(Note 6)
80
(Note 6)
81
82
(Note 1)
83
(Note 2)
84
(Note 1)
85
(Note 2)
86
(Note 1)
87
(Note 2)
88
Parameter Name
(Command Reference)
Demodulator Spectrum Rotation
(ref. 'DSR_' command).
Reed-Solomon Encoder Enable
(ref. 'RSEN_' command).
Reed-Solomon Decoder Enable
(ref. 'RSDE_' command).
Backward Alarm enable TX1
(ref. 'BW_TX1_' command).
Backward Alarm enable TX2
(ref. 'BW_TX2_' command).
Backward Alarm enable TX3
(ref. 'BW_TX3_' command).
Backward Alarm enable TX4
(ref. 'BW_TX4_' command).
Backward Alarm enable RX1
(ref. 'BW_RX1_' command).
Backward Alarm enable RX2
(ref. 'BW_RX2_' command).
Backward Alarm enable RX3
(ref. 'BW_RX3_' command).
Backward Alarm enable RX4
(ref. 'BW_RX4_' command).
SCT Reference Clock
(ref. 'MSPR_' command).
ASYNC TX Overhead Baud Rate
(ref. 'TOBR_' command).
ASYNC RX Overhead Baud Rate
(ref. 'ROBR_' command).
ASYNC TX Channel Char. Length
(ref. 'TCCL_' command).
ASYNC RX Channel Char. Length
(ref. 'RCCL_' command).
ASYNC TX Channel Stop Bits
(ref. 'TCSB_' command).
ASYNC RX Channel Stop Bits
(ref. 'RCSB_' command).
Description
p71 = n, where 'n' is '0' (NRM), '1' (INV).
p72 = n, where 'n' is '0' (off) or '1' (on).
p73 = n, where 'n' is '0'(OFF), '1' (ON), '2' (CORR_OFF).
p74 = n, where 'n' is '0'(OFF), or '1' (ON).
p75 = n, where 'n' is '0'(OFF), or '1' (ON).
p76 = n, where 'n' is '0'(OFF), or '1' (ON).
p77 = n, where 'n' is '0'(OFF), or '1' (ON).
p78 = n, where 'n' is '0'(OFF), or '1' (ON).
p79 = n, where 'n' is '0'(OFF), or '1' (ON).
p80 = n, where 'n' is '0'(OFF), or '1' (ON).
p81 = n, where 'n' is '0'(OFF), or '1' (ON).
p82 = n, where 'n' is '0' (MR), '1' (ERF).
p83 = nnnnn, where 'nnnnn' is the currently programmed
baud rate.
P84 = nnnnn, where 'nnnnn' is the currently programmed
baud rate.
p85 = n, where 'n' is the currently programmed character
length (7 or 8 bits).
p86 = n, where 'n' is the currently programmed character
length (7 or 8 bits).
p87 = n, where 'n' is the currently programmed number of
stop bits (1 or 2).
p88 = n, where 'n' is the currently programmed number of
stop bits (1 or 2).
A–41
Revision 4
MN/SLM7650.IOM