Table of Contents
Advertisement
SLM-7650 Satellite Modem
Remote Control Specifications
Modulator /
Command:
Coder Config.
Response:
Program
Status
<add/MCP_'cr'
>add/MCP_'cr'
SMT_xxxxxxx'cr'
RMR_'cr'
MET_xxx'cr'
ITOT_xxxxx'cr'
MOM_xxxxxxx'cr'
MT_xxxxx'cr'
MF_nn.nnnnnn'cr'
MR_nnnn_mmmmm.mmm'cr'
MPO_snn.n'cr'
LPC_xxx'cr'
MOP_snn.n'cr'
SE_xxx'cr'
DENC_xxx'cr'
ERF_nnnnnn.n'cr'
TC_xxxx'cr'
TCP_xxxx'cr'
BBL_xxx'cr'
ILT_xxx'cr'
TIF_xxxxx'cr'
ICFT_xxxxx'cr'
ISP_xxx'cr'
TDF_xxxx'cr'
TET_xxxxx'cr'
ISCL_TX1_nnn'cr'
ISCL_TX2_nnn'cr'
TDP_xxxx'cr'
DDF_xxxxxx'cr'
BDCA_dd;cc_dd;cc...'cr'
DIL_xx'cr'
MRC_xxx'cr'
MSR_xxx'cr'
RSEN_xxx'cr'
BW_TX1_nnn'cr'
BW_TX2_nnn'cr'
BW_TX3_nnn'cr'
BW_TX4_nnn'cr'
MSPR_xxxx'cr'
TAS_xx'cr'
TOBR_nnnnn'cr'
TCCL_nnn'cr'
TCSB_nnn'cr'
TOCP_nnn'cr'
ACT_xxxxx'cr'
NOMP_snn.n'cr'
MINP_snn.n'cr'
MAXP_snn.n'cr'
LCL_xxxx'cr'
RCL_xxxx'cr'
RTSM_xxx'cr'
TDA_xxx'cr'
COM_xxxxxx'cr'
SCRT_xxxx'cr'
T310_xxx'cr'
MRSC_nnn_kkk_i'cr'
RF_xxx'cr''lf']
System Modem Type
Reset Mod Rate (reserved for Comtech switch)
Modulator Encoder Type
Interface Transmit Overhead Type
Modem Operation Mode
Modulator Type
Modulator Frequency
Modulator Rate
Modulator Power Offset
(Note 3)
AUPC Local Power Enable
(Note 2)
Modulator Output Power
Scrambler Enable
Differential Encoder
External Reference Frequency
Transmit Clock (Source)
Transmit Clock Phase
Baseband Loopback
Interface Loop Timing
(Note 7)
Terrestrial Interface Format
(Note 7)
Interface Coding Format Transmit
Interface Substitution Pattern (TX 2047)
Transmit Data Fault
(Note 5)
IDR Transmit ESC Type
(Note 5)
Service Channel Level TX1
(Note 5)
Service Channel Level TX2
Transmit Data Phase
(Note 6)
Drop Data Format
(Note 6)
Bulk Drop Channels Assignment
(Note 6)
DDO/IDI Loopback
Modem Reference Clock
Modulator Spectrum Rotation
Reed-Solomon Encoder
(Note 5)
Backward Alarm Enable TX1
(Note 5)
Backward Alarm Enable TX2
(Note 5)
Backward Alarm Enable TX3
(Note 5)
Backward Alarm Enable TX4
SCT PLL Reference
(Note 8)
Terrestrial ASYNC Source
(Note 1)
ASYNC Transmit Overhead Baud Rate
(Note1)
ASYNC Transmit Channel Character Length
(Note1)
ASYNC Transmit Channel Stop Bits
(Note1)
ASYNC Transmit Channel Parity
(Note 1)
ASYNC Communications Type
(Note 3)
AUPC Nominal Power Value
(Note 3)
AUPC Minimum Power Value
(Note 3)
AUPC Maximum Power Value
(Note 3)
AUPC Local Carrier Loss
(Note 3)
AUPC Remote Carrier Loss
RTS TX-IF Control Mode
Transmit BPSK Data Ordering
Carrier Only Mode
Scrambler Type
TX 8PSK IESS-310 Operation
(Note 4)
Reed-Solomon Codeword
RF Output (ON/OFF)
Note: This command is used by the EF Data M:N protection
switch to collect information that is necessary to configure
back-up modems. Because this command (content and/or
order) can be changed at any time by EF Data, it is advisable
that other commands ('MCS_' and 'ICS_', or 'BCS_') be used
for M&C systems.
A–24
Revision 4
MN/SLM7650.IOM
Advertisement
Table of Contents
