Table of Contents
Advertisement
SLM-7650 Satellite Modem
Remote Control Specifications
Demod/
Command:
Decoder
Resp onse:
Config.
Program
Status
<add/DCP_'cr'
>add/DCP_'cr'
SMT_xxxxxxx'cr'
RDR_'cr'
DDT_xxx'cr'
IROT_xxxxx'cr'
MOM_xxxxxxx'cr'
BERT_xxxx'cr'
DT_xxxx'cr'
DF_nn.nnnnnn'cr'
DR_nnnn_mmmmm.mmm'cr'
DCRT_xxxx'cr'
DE_xxx'cr'
DDEC_xxx'cr'
IFL_xxx'cr'
SCF_snnnnn'cr'
SWR_nnnnn'cr'
SR_xxx'cr'
ERF_nnnnnn.n'cr'
BC_xxx'cr'
RCP_xxxx'cr'
BBL_xxx'cr'
ILT_xxx'cr'
TIF_xxxxx'cr'
(Note 6)
ICFR_xxxx'cr'
(Note 6)
IBP_xxx'cr'
IRE_xxxxxx'cr'
RDF_xxxx'cr'
RET_xxxxx'cr'
(Note 4)
ISCL_RX1_nnn'cr'
(Note 4)
ISCL_RX2_nnn'cr'
(Note 4)
RDP_xxxx'cr'
IDF_xxxxxx'cr'
(Note 5)
BICA_dd;cc_dd;cc...'cr'
(Note 5)
DIL_xx'cr'
(Note 5)
IBS _nnnnnn'cr'
DSR_xxx'cr'
RSDE_xxx'cr'
BW_RX1_nnn'cr'
(Note 4)
BW_RX2_nnn'cr'
(Note 4)
BW_RX3_nnn'cr'
(Note 4)
BW_RX4_nnn'cr'
(Note 4)
TAS_xx'cr'
(Note 7)
ROBR_nnnnn'cr'
(Note 1)
RCCL_nnnnn'cr'
(Note 1)
RCSB_nnnnn'cr'
(Note 1)
ROCP_nnnnn'cr'
(Note 1)
ACT_xxxxx'cr'
(Note 1)
ENSP_nn.n'cr'
(Note 2)
MAXT_n.n'cr'
(Note 2)
RDA_xxx'cr'
R310_xxx'cr'
DRSC_nnn_kkk_i'cr''lf']
(Note 3)
System Modem Type
Reset Demod Rate (reserved for Comtech switch)
Demodulator Decoder Type
Interface Receive Overhead Type
Modem Operation Mode
BER Threshold
Demodulator Type
Demodulator Frequency
Demodulator Rate
Descrambler Type
Descrambler Enable
Differential Decoder
IF Loopback
Sweep Center Frequency
Sweep Width Range
Sweep Reacquisition
External Reference Frequency
Buffer Clock
Receive Clock Phase
Baseband Loopback
Interface Loop Timing
Terrestrial Interface Format
Interface Coding Format Receive
Interface Buffer Programming
Interface Read Error (RX 2047)
Receive Data Fault
IDR Receive ESC Type
Service Channel Level RX1
Service Channel Level RX2
Receive Data Phase
Insert Data Format
Bulk Insert Channels Assignment
DDO/IDI Loopback
Interface Buffer Size
Demodulator Spectrum Rotation
Reed-Solomon Decoder
Backward Alarm Enable RX1
Backward Alarm Enable RX2
Backward Alarm Enable RX3
Backward Alarm Enable RX4
Terrestrial ASYNC Source
ASYNC Receive Overhead Baud Rate
ASYNC Receive Channel Character Length
ASYNC Receive Channel Stop Bits
ASYNC Receive Channel Parity
ASYNC Communications Type
AUPC EBN0 Target Set Point
AUPC Max. Tracking Rate
Receive BPSK Data Ordering
RX 8PSK IESS-310 Operation
Reed-Solomon Codeword
This command is used by the EF Data M:N protection switch
to collect information that is necessary to configure back-up
modems. Because this command (content and/or order) can
be changed at any time by EF Data, it is advisable that other
commands ('DCS_' and 'ICS_', or 'BCS_') be used for M&C
systems.
Notes:
1. Data is only returned for RX ASYNC Overhead.
2. Data is only returned for RX ASYNC Overhead.
3. Data is only returned when the modem type is set to
CUSTOM and RX Overhead is either NONE or
ASYNC.
A–27
Revision 4
MN/SLM7650.IOM
Advertisement
Table of Contents
