Comtech EF Data SLM-7650 Installation And Operation Manual page 162

SLM-7650 Satellite Modem
Remote Control Specifications
A.11 System Configuration Commands
Time Of Day Command:
Response:
Status:
Response:
Date Command:
Response:
Status:
Response:
Remote Command:
Response:
Clear Stored Command:
Faults Response:
Modem Command:
Reference Response:
Clock
Status:
Response:
Modem Command:
Operation Response:
Mode
Status:
Response:
System Command:
Modem Type Response:
Status:
Response:
Save Modem Command:
Config. Response:
Recall Modem Command:
Config. Response:
<add/TIME_hh:mm:ss'cr'
>add/TIME_hh:mm:ss'cr''lf']
<add/TIME_'cr'
>add/TIME_hh:mm:ss'cr''lf']
<add/DATE_mm/dd/yyyy'cr'
>add/DATE_mm/dd/ttyy'cr''lf']
<add/DATE_'cr'
>add/DATE_mm/dd/yyyy'cr''lf']
<add/REM_'cr'
>add/REM_'cr''lf']
<add/CLSF_'cr'
>add/CLSF_'cr''lf']
<add/MRC_xxxxx'cr'
>add/MRC_xxxxx'cr''lf']
<add/MRC_'cr'
>add/MRC_xxxxx'cr''lf']
<add/MOM_xxxxxxx'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/MOM_'cr'
>add/MOM_xxxxxxx'cr''lf']
<add/SMT_xxxxxx'cr'
>add/SMT_xxxxxx'cr'
RF_OFF'cr''lf']
<add/SMT_'cr'
>add/SMT_xxxxxx'cr''lf']
<add/SMC_n'cr'
>add/SMC_n'cr''lf']
<add/RMC_n'cr'
>add/RMC_n'cr''lf']
Where:
hh = 0 to 23 (hours).
mm = 00 to 59 (minutes).
ss = 00 to 59 (seconds).
Where:
mm = 1 to 12 (month).
dd = 1 to 31 (day).
yyyy = 2000 to 2099 (year).
Configures the modem for remote operation.
The SLM7650 will respond to any status request at any
time. However, the SLM7650 must be in 'Remote Mode' to
change configuration parameters.
This command is used to clear all stored faults logged by
the SLM7650.
Where: xxxxx = INT (INTERNAL), EXT1 (EXTERNAL 1
MHz), EXT5 (EXTERNAL 5 MHz), EXT10 (EXTERNAL 10
MHz), EXT20 (EXTERNAL 20 MHz).
Where: xxxxxxx = TX_ONLY, RX_ONLY, DUPLEX mode.
This command configures the modem for simplex, duplex or
standby operation modes. When transmit only mode is
selected, receive faults are inhibited and when receive only
mode is selected, transmit faults are inhibited.
Where: xxxxxx = IDR, IBS, DI, ASYNC, EFD, CUSTOM,
IBS-309, VSAT-IBS, 7650.00 or 7650.02.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command saves the current modem configuration for
recall at a later time using the 'RMC_' command. Up to five
different modem configurations can be saved.
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command causes the modem to be reprogrammed with
configuration parameters previously saved using the 'SMC_'
command. One of five saved configurations can be
specified.
A–20
Revision 4
MN/SLM7650.IOM