Table Of Contents; Accessories Supplied; Introduction; Features - GME GA9800 Instruction Manual

gme strongly recommends that you keep this manual
AccEssoriEs suPPliED . . . . . . . . . . . . . . . . . . . . 2
introDuction . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FEAturEs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ProtEction circuitry . . . . . . . . . . . . . . . . . . . 2
2 ohm ProtEction . . . . . . . . . . . . . . . . . . . . . . 3
ElEctricAl WirinG . . . . . . . . . . . . . . . . . . . . . . 3
FusEs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
mountinG thE AmPliFiEr . . . . . . . . . . . . . . . . . 3
PoWEr suPPly connEctions . . . . . . . . . . . . . . 3
Four chAnnEl instAllAtion WirinG
1 . low input wiring 2 channel . . . . . . . . . . . . . . . . 4
2 . high input wiring . . . . . . . . . . . . . . . . . . . . . . . 5
• Subwoofer wire
• Remote Control
• Mounting screws

INTRODUCTION

congratulations on your purchase of the GmE GA9800
marine audio amplifier .
this amplifier is designed to the highest level of quality and
will offer you years of listening enjoyment .
thank you for making GmE your choice for marine audio
equipment .

FEaTURES

• Thermal/Short/Over Load Protection
• 2 Ohm stable (4 Ohm bridged)
• P.W.M.MOSFET power supply
• Power and distress indicator
• Variable low-pass (50-120 Hz)
• Heavy duty heat sink
• Adjustable input sensitivity
• Soft delayed remote turn-on
• Low level and high level input
• Nickel plated terminal strips/RCA jacks
PA G E 2
in a safe place for future reference
CONTENTS

aCCESSORIES SUPPlIED

• Allen keys
• Instruction Manual
i n s t r u c t i o n m A n u A l
3 . low input wiring 4 channel . . . . . . . . . . . . . . . . 6
sPEAKEr conFiGurAtion
1 . 4/8-way speaker . . . . . . . . . . . . . . . . . . . . . . . . 7
2 . 2-way speaker and subwoofer . . . . . . . . . . . . . . 8
3 . 2-way speaker and 2-way subwoofer . . . . . . . . . 9
4 . 4-way speaker and 2-way subwoofer . . . . . . . . . 9
AmPliFiEr instAllAtion . . . . . . . . . . . . . . . . . . 10
rEmotE control . . . . . . . . . . . . . . . . . . . . . . 10
PrEcAutions . . . . . . . . . . . . . . . . . . . . . . . . . . 10
sPEciFicAtions . . . . . . . . . . . . . . . . . . . . . . . . . 10
troublEshootinG . . . . . . . . . . . . . . . . . . . . . . 11
WArrAnty . . . . . . . . . . . . . . . . . . . . . . back Page
if any items are missing or
damaged, please contact your
retailer or place of purchase .
• Built-in remote jack
• Built-in electronic Crossover and an adjustable
low Pass control
• Designed with 100% MOSFET Power supply, ensuring
extremely quick switching response and self-protection .

PROTECTION CIRCUITRy

the amplifier protection circuitry will disable the amplifier if
input overload, short circuit or extremely high temperature
conditions are detected . When the protection mode is in
operation, the LED indicator on the front panel will be
illuminated, indicating the amplifier has gone into a
self-preservation mode .
lf you observe that the protection LED is lit, please check
the system carefully to determine what has caused the
protection circuit to engage . the amplifier can be reset by
turning the remote power oFF and then on again . lf the
amplifier shuts down due to a thermal overload condition,
please allow it to cool down before restarting . lf the shut
down is due to an input overload or short circuit, be sure
to repair these conditions before attempting to power up
the amplifier again .
G A 9 8 0 0