Entering, Storing And Sending Selcalls; Call Acknowledge; Storing Selcall Idents; Recalling Selcall Idents From The Memory - GME GA9800 Instruction Manual

Memory location 11 holds the Selcall Ident for the Pager
function . See the 'Page Mode' section for more details on this
feature . When in ALPHA mode, this memory displays 'PAGER' .
Memory location 12 holds the last-sent or received
Selcall Ident . Whenever you send or receive a Selcall, the
Ident is automatically stored in this location allowing you
to easily recall it and resend it . When in ALPHA mode, this
memory displays 'LAST' .
Memory location 13 contains the radio's own Selcall
Ident . If you need to give your Selcall Ident to someone but
can't remember it, you can recall it from this location . When
in ALPHA mode, this memory displays 'RADIO' .
The memories can be viewed by briefly pressing the CALL
button on the microphone, then rotating the
Channel switch .
ENTERING, STORING AND SENDING
SELCALLS
Use the following procedure to enter and send a Selcall .
1 . P ress the CALL button on the microphone . 'CALL TO' is
displayed, along with a memory location on the left and
an associated 5 digit Selcall Ident on the lower right .
Memory Location
2 . Enter the required Selcall ident as follows:
(a) B riefly press the Channel knob . The right-hand digit
of the Selcall Ident will flash .
(b) R otate the Channel knob to select the required
number in the flashing digit position .
(c) B riefly press the Channel knob again to select the
next digit position .
(d) R epeat steps (b) and (c) to enter all 5 digits
as required .
3 . Now press and hold the CALL button to send the Ident .

CALL ACKNOWLEDGE

If your Selcall transmission is successful, the radio you called
should respond with a 'call acknowledge' signal - usually
two quick beeps . This will confirm to you that the radio you
called is now alerting its user to your signal .
T X 4 4 0 0
CALL TO
Mode selected
Selcall Ident
I NST RUC TIO N M AN UAL

STORING SELCALL IDENTS

Your TX4400 is fitted with 10 user programmable Selcall
Ident memories, allowing you to store up to 10 frequently
used Selcall Idents . The memories are accessed by pressing
the CALL button on the microphone then rotating the
Channel switch .
Note: Memory locations 1 - 4 are 'Fast Dial' memories .
Once programmed they can be quickly recalled using the
front panel keys . If you wish to make use of this feature,
you should program your four most frequently used Selcall
idents into the first four memory locations . For details on
using these 'Fast Dial' keys, see section below on
'Recalling Fast Dial Memories' .
To Store a Selcall Ident in memory
1 . P ress the CALL button on the microphone to select the
'CALL TO' mode . 'CALL TO' is displayed along with a
memory location number on the left and an associated 5
digit Selcall Ident on the right .
2 . R otate the Channel switch to select the Selcall memory
that you wish to programme (only locations 1 - 10 are
available for user programming) .
Note: If the radio displays letters instead of numbers in
the Selcall Ident position, your radio is in ALPHA mode . To
switch back to Ident mode, briefly press the F key then the
ALPHA key .
3 . W ith the required memory location displayed, enter the
Selcall ident as follows:
(a) B riefly press the Channel knob . The right-hand digit
of the Selcall Ident will flash .
(b) R otate the Channel knob to select the required
number in the flashing digit position .
(c) B riefly press the Channel knob again to select the
next digit position .
(d) R epeat steps (b) and (c) to program all 5 digits as
required .
3 . N ow press and hold the Channel knob . The Selcall Ident
will flash for a few seconds, then the radio will beep as
the Ident is stored .
RECALLING SELCALL IDENTS FROM THE
MEMORY
1 . B riefly press the CALL button on the microphone to
select the 'CALL TO' mode .
2 . R otate the Channel knob to select the required memory
location . The Selcall ident stored in that memory will be
displayed .
3 . W hen the required Selcall Memory is displayed, press and
hold the CALL button to send the Ident .
PAG E 11