Installation - GME GA9800 Instruction Manual

tone set and frequency that matches theirs. the tX3340 includes
most of the commonly used tone sets.
if the users you talk to don't currently use ctcss or dcs you can
make your own choice. there is no difference in performance or
function between the different tone sets.
To select a CTCSS or DCS tone
Note:
When selecting tones, ctcss tones are prefixed with 'ctc'
and dcs tones are prefixed with 'dc'.
1. Press and hold the MENU key until the radio beeps.
2. Briefly press the MENU key repeatedly until 'ctcxx' or 'dcxxx'
is displayed (where xx represents a tone number in the ctcss/
dcs tone Frequency chart).
3. Press the or keys to scroll through the tone list and select
the required ctcss or dcs tone. scroll upwards for dcs tones
and downwards for ctcss tones.
if you wish to view the ctcss frequency or dcs tone instead
of the table number, briefly press the PRI key. to return to
the table code briefly press the PRI key again or wait for it to
time-out.
4. to disable ctcss or dcs tones altogether scroll to the bottom of
the list and select 'ctcoF'.
5. to store the setting, press and hold the MENU key until the
radio beeps.
BacKlighting
Backlighting can be set to hiGh, loW or oFF to satisfy your
personal preference.
1. Press and hold the MENU key until the radio beeps.
2. Briefly press the MENU key repeatedly until 'liGht' is displayed.
3. Press the key to increase the backlight or the
decrease the backlight.
4. Press and hold the MENU key until the radio beeps, to store
the setting.
DiSplay colour
the colour of the back light display can be changed to suit your
installation environment.
to change the back light colour:
1. Press and hold the MENU key until the radio beeps.
2. Briefly press the MENU key repeatedly until 'color'
is displayed.
PA G E 1 5
3. Press the
back light colours.
4. Press and hold the MENU key until the radio beeps to store
the settings.
Battery / S-meter / alpha Selection
the tX3340 has the option of displaying either the battery voltage
or the incoming signal strength (s-meter) in the area beneath the
channel display.
To display S-Meter or Battery Voltage
1. Press and hold the MENU key until the radio beeps.
2. Briefly press the MENU key repeatedly until 's-mEt' (s meter) or
'bAtt' (Battery) is displayed.
3. Press the
S-MET or bATT.
4. Press and hold the MENU key until the radio beeps, to store
the setting.
Beep
to adjust the volume level of the keypad beeps:
1. Press and hold the MENU key until the radio beeps.
2. Briefly press the MENU key repeatedly until 'BEEP' is displayed.
3. Press the
setting is '3'.
4. to store the setting, press and hold the MENU key until the
radio beeps.
the tX3340 main unit is supplied with a slim, u-shaped mounting
cradle. the cradle can be screwed or bolted in any convenient
location in your vehicle (under or above the dash, on the centre
key to
console, etc.) using the mounting slots provided in the cradle.
the tX3340 contains a built-in speaker, and should be installed
in a convenient location in the vehicle's cabin as the radio's loud
speaker. Alternatively it can be installed in a less audible location
and an extension speaker used instead.
the lcd controller microphone comes complete with a mounting
clip. its small size and light weight design allows it to be mounted
in almost any convenient position accessible to the driver.
When installing the radio, avoid mounting it close to heaters or
air conditioners. screw the lcd controller microphone's clip to a
firm surface. Fit the tX3340 into the cradle and tighten the gimbal
knobs. Place the lcd controller microphone in its mounting clip.
i n s t r u c t i o n m A n u A l
or keys to cycle through yellow, red or Green
or keys to select your preferred choice of
or keys to adjust the beep volume. the default

INSTAllATION

t X 3 3 4 0