GME GA9800 Instruction Manual page 208

to cancel the alarm and listen on the channel
Briefly press the QuiEt key (if quiEt has been activated).
the alarm will stop beeping and the channel will remain
open to any incoming signals.
QuiEt moDE (Q)
quiEt mode mutes the tX3440's receiver to prevent any
incoming signals from being heard in the speaker until your
selcall ident is received. in this way you can monitor
a busy channel for personal calls without being disturbed
by unwanted signals.
if your selcall ident is received, quiEt mode is then
cancelled and all incoming signals are heard in the speaker.
setting up QuiEt mode
to setup quiEt mode you must first 'tag' the channels
that you want to stay quiet, then activate the quiEt mode.
once quiEt mode is activated, the channels you have
tagged will remain quiet to all incoming signals unless
your selcall ident is received. channels not tagged will
remain open to all signals and will operate normally.
to tag individual
channels for QuiEt operation
1. select the required channel by pressing the
2. Press and hold the QuiEt key until the radio beeps. 'q'
will appear to the right of the channel display indicating
the selected channel is now tagged for quiet operation.
to remove the QuiEt tag
from individual channels:
1. select a channel that has been tagged for quiet
operation. 'q' will be displayed.
2. Press and hold the QuiEt key until the radio beeps. 'q'
will disappear indicating this channel is no longer tagged
for quiet operation.
activating QuiEt mode
1. First, select a channel that has been tagged for quiet
operation (you cannot activate quiet mode unless you
have selected a 'tagged' channel). 'q' will be displayed.
2. now briefly press the QuiEt key. 'quiEt' will appear
on the display.
now all channels that were tagged for quiet operation will
be operating in the quiEt mode.
Deactivating QuiEt mode
1. select any channel that has been tagged for quiet
operation. 'q' and 'quiEt' will be displayed.
t X 3 4 4 0
2. Briefly press the F key followed by the QuiEt key.
'quiEt' will disappear from the display and all channels
that were tagged for quiet operation will now operate
normally again.
receiving signals in QuiEt mode
• If a normal signal is received on a QUIET channel, the
channel will appear busy (the 'BusY' indicator will be
visible) but no sound will be heard from the speaker.
this means you will not be disturbed by the signal.
• If a normal signal is received on an open channel (one
that is not tagged with 'q') the signal will be heard in
the usual way.
• If a signal containing your Selcall Ident is received
on any channel (open or quiEt) quiEt mode will be
cancelled and the alarm will beep to alert you to the
call. in addition, the caller's ident or AlPHA name will
be displayed. All channels will now be open for normal
transmission and reception.
if you wish to respond to the calling radio using selcall,
press and hold the call key for 1.5 seconds until the radio
beeps. the callers ident will be transmitted back to them
causing the alarm in their radio to be activated.
or keys.
to cancel the alarm on your radio
Briefly press the ptt key.
to return your radio to the QuiEt mode
Briefly press the F key followed by the QuiEt key. 'quiEt'
will re-appear on the display.
scanning in QuiEt moDE
the tX3440 will allow you to scan while quiEt mode is
active. using this feature you can monitor a group of quiet
channels or a combination of quiet and open channels.
to scan in QuiEt mode
1. Pre-select the scan mode.
2. select the channels you wish to scan and store them in
the scan memory.
3. From those channels, select the ones you wish to remain
quiet and tag each one for quiEt operation.
4. select a tagged channel and activate quiEt mode
(press the QuiEt key).
5. Press the scan key. the radio will begin scanning
and 'scAn' and 'quiEt' will be displayed, indicating
the radio is scanning in quiEt mode.
i n s t r u c t i o n m A n u A l PA G E 1 1