Table of Contents
Advertisement
SDM-300L3 Satellite Modem
Remote Control Operation
Interface
Command:
Config.
Response:
Status
<add/ICS_'cr'
>add/ICS_'cr'
TC_xxxx'cr'
ERF_nnnnn.n'cr'
TCP_xxxx'cr'
RCP_xxxx'cr'
BBL_xxx'cr'
ILB_xxx'cr'
ILT_xxx'cr'
ICFT_xxxx'cr'
ICFR_xxxx'cr'
BC_xxx'cr'
IRFS_T1_ssss'cr'
IRFS_E1_ssss'cr'
IBP_xxx'cr'
IBS _nnnnnn'cr'
ITOT_xxxxx'cr'
IROT_xxxxx'cr'
ISP_xxxxxx'cr'
IRE_xxxxxx'cr'
TDF_xxxx'cr'
RDF_xxxx'cr
ISCL_TX1_nnn'cr'
ISCL_TX2_nnn'cr'
ISCL_RX1_nnn'cr'
ISCL_RX2_nnn'cr'
TDP_xxxx'cr'
RDP_xxxx'cr'
DDF_xxxxxx'cr'
(Note 1)
BDCA_dd;cc_dd;cc...'cr' (Note 1)
ICRC_xxx'cr'
(Note 2)
IDF_xxxxxx'cr'
(Note 2)
BICA_dd;cc_dd;cc...'cr'
(Note 2)
BW_TX1_nnn'cr'
(Note 3)
BW_TX2_nnn'cr'
(Note 3)
BW_TX3_nnn'cr'
(Note 3)
BW_TX4_nnn'cr'
(Note 3)
BW_RX1_nnn'cr'
(Note 4)
BW_RX2_nnn'cr'
(Note 4)
BW_RX3_nnn'cr'
(Note 4)
BW_RX4_nnn'cr'
(Note 4)
TXDR_xxxxxx'cr'
RXDR_xxxxxx'cr'
TOBR_nnnnn'cr'
(Note 5)
TCCL_n'cr'
(Note 5)
TCSB_n'cr'
(Note 5)
TOCP_xxxx'cr'
(Note 5)
TCT_xxxxx'cr'
(Note 5)
ROBR_nnnnn'cr'
(Note 6)
RCCL_n'cr'
(Note 6)
RCSB_n'cr'
(Note 6)
ROCP_xxxx'cr'
(Note 6)
RCT_xxxxx'cr'
(Note 6)
LPC_xxx'cr'
(Note 5)
NOMP_snn.n'cr'
(Note 5)
Notes:
1. Data is only returned for RX D&I overhead (or Flex Mux
D&I mode).is installed.
2. Data is only returned for RX IDR Overhead.
3. Data is only returned for RX ASYNC Overhead.
4. Not Used.
5. Not Used.
6. Not Used.
7. Not Used.
8. Data is only returned for RX ASYNC/AUPC Overhead.
9. Data is only returned for the TX/RF L-Band modem
Transmit Clock (Source)
External Reference Frequency
Transmit Clock Phase
Receive Clock Phase
Baseband Loopback
Interface Loopback
Interface Loop Timing
Interface Coding Format Transmit
Interface Coding Format Receive
Buffer Clock (Source)
Interface Receive Frame Structure (T1)
Interface Receive Frame Structure (E1)
Interface Buffer Programming
Interface Buffer Size
Interface Transmit Overhead Type
Interface Receive Overhead Type
Interface Substitution Pattern (TX 2047)
Interface Read Error (RX 2047)
Transmit Data Fault
Receive Data Fault
Service Channel Level TX1
Service Channel Level TX2
Service Channel Level RX1
Service Channel Level RX2
Transmit Data Phase
Receive Data Phase
Drop Data Format
Bulk Drop Channels Assignment
Insert E1 CRC Enable
Insert Data Format
Bulk Insert Channels Assignment
Backward Alarm Enable TX1
Backward Alarm Enable TX2
Backward Alarm Enable TX3
Backward Alarm Enable TX4
Backward Alarm Enable RX1
Backward Alarm Enable RX2
Backward Alarm Enable RX3
Backward Alarm Enable RX4
TX Driver Type
RX Driver Type
ASYNC Transmit Overhead Baud Rate
ASYNC Transmit Channel Character Length
ASYNC Transmit Channel Stop Bits
ASYNC Transmit Overhead Channel Parity
ASYNC Transmit Communications Type
ASYNC Receive Overhead Baud Rate
ASYNC Receive Channel Character Length
ASYNC Receive Channel Stop Bits
ASYNC Receive Overhead Channel Parity
ASYNC Receive Communications Type
AUPC Local Power Enable
AUPC Nominal Power Value
A–24
Revision 1
MN/SDM300L3.IOM
Advertisement
Table of Contents
