Table of Contents
Advertisement
SDM-300L3 Satellite Modem
Remote Control Operation
Recall
Command:
Modem
Response:
Config.
Local
Command:
Modem
Response:
AUPC
Status:
Mode
Response:
RTS TX-IF
Command:
Control
Response:
Mode
Status:
Response:
RF Mode
Command:
Control
Response:
Status:
Response:
A.3.5
Automatic Uplink Power Control (AUPC)
AUPC Local
Command:
Enable
Response:
Status:
Response:
AUPC
Command:
Nominal
Response:
Power Level
Status:
Response:
AUPC
Command:
Maximum
Response:
Power Limit
Status:
Response:
<add/RMC_n'cr'
>add/RMC_n'cr''lf']
<add/LMA_xxx'cr'
>add/LMA_xxx'cr''lf']
<add/LMA_'cr'
>add/LMA_xxx'cr''lf']
<add/RTSM_xxx'cr'
>add/RTSM_xxx'cr''lf']
<add/RTSM_'cr'
>add/RTSM_xxx'cr''lf']
<add/RFMD_xxxx'cr'
>add/RFMD_xxxx'cr''lf']
<add/RFMD_'cr'
>add/RFMD_xxxx'cr''lf']
<add/LPC_xxx'cr'
>add/LPC_xxx'cr''lf']
<add/LPC_'cr'
>add/LPC_xxx'cr''lf']
<add/NOMP_snn.n'cr'
>add/NOMP_snn.n'cr''lf']
<add/NOMP_'cr'
>add/NOMP_snn.n'cr''lf']
<add/MAXP_snn.n'cr'
>add/MAXP_snn.n'cr''lf']
<add/MAXP_'cr'
>add/MAXP_snn.n'cr''lf']
Where: n = 1, 2, 3, 4, or 5 (stored configuration number).
This command causes the modem to be reprogrammed
with configuration parameters previously saved using the
'SMC_' command. One of five saved configurations can
be specified.
Where: xxx = ON or OFF.
This command configures the modem for the LOCAL
MODEM AUPC mode. When 'ON' is selected, the AUPC
configuration can be entered.
Where: xxx = ON or OFF.
This command configures the modem for the RTS TX-IF
control mode. If 'ON' is selected, the TX-IF output will only
be turned on if the incoming RTS signal is asserted (also
the TX-IF output has to be programmed ON and no major
modulator faults are present). If 'OFF' is selected, the TX-
IF output will operate normal ignoring the RTS signal.
Where: xxxx = NRM (Normal Mode), PWR (Turn RF off on
power up), COMM (Turn RF off on power up and loss of
remote communications after 10 seconds), CD (Turn RF
ON when carrier is detected, turn RF OFF when no carrier
is detected. For the RF ON condition, the TX-IF must be
programmed ON. Note: RTS TX-IF, when enabled over-
rides CD).
This command allows for the RF output to be enabled or
disabled depending on the following described conditions.
One application for this command will be in demand
network systems.
Where: xxx = ON or OFF.
Notes:
1. When programmed ON, the MOP (Modulator
Output Power) command is not allowed, only MOP
status is allowed.
3.
ASYNC or AUPC Overhead only.
Where: snn.n = -30.0 to -5.0, in 0.1 steps (nominal range
in dBm).
Notes:
1. The nominal power range is modified relative to
the value specified by the modulator power offset
(MPO_).
2. ASYNC or AUPC Overhead only.
Where: snn.n = -30.0 to -5.0, in 0.1 steps (nominal range
in dBm).
Notes:
1. The nominal power range is modified relative to
the value specified by the modulator power offset
(MPO_).
2. ASYNC or AUPC Overhead only.
A–15
Revision 1
MN/SDM300L3.IOM
Advertisement
Table of Contents
