Comtech EF Data SDM-300L3 Installation And Operation Manual page 363

SDM-300L3 Satellite Modem
Remote Control Operation
Interface Command:
Coding Response:
Format Status:
Receive Response:
Transmit Command:
Data Fault Response:
Status:
Response:
Receive Command:
Data Fault Response:
Status:
Response:
Interface Command:
Service Response:
Channel Status:
Level Response:
IDR Command:
Backward Response:
Alarm Status:
Enable Response:
Drop Data Command:
Format Response:
Status:
Response:
Insert Data Command:
Format Response:
Status:
Response:
Insert E1 Command:
CRC Response:
Enable Status:
Response:
Drop Command:
Channels Response:
Assignment Status:
Response:
<add/ICFR_xxxx'cr'
>add/ICFR_xxxx'cr''lf']
<add/ICFR_'cr'
>add/ICFR_xxxx'cr''lf']
<add/TDF_xxxx'cr'
>add/TDF_xxxx'cr''lf']
<add/TDF_'cr'
>add/TDF_xxxx'cr''lf']
<add/RDF_xxxx'cr'
>add/RDF_xxxx'cr''lf']
<add/RDF_'cr'
>add/RDF_xxxx'cr''lf']
<add/ISCL_xxx_snn'cr'
>add/ISCL_xxx_snn'cr''lf']
<add/ISCL_xxx'cr'
>add/ISCL_xxx_snn'cr''lf']
<add/BW_xxx_nnn'cr'
>add/BW_xxx_nnn'cr''lf']
<add/BW_xxx'cr'
>add/BW_xxx_nnn'cr''lf']
<add/DDF_xxxxxx'cr'
>add/DDF_xxxxxx'cr''lf']
<add/DDF_'cr'
>add/DDF_xxxxxx'cr''lf']
<add/IDF_xxxxxx'cr'
>add/IDF_xxxxxx'cr''lf']
<add/IDF_'cr'
>add/IDF_xxxxxx'cr''lf']
<add/ICRC_xxx'cr'
>add/ICRC_xxx'cr''lf']
<add/ICRC_'cr'
>add/ICRC_xxx'cr''lf']
<add/DCA_dd;cc'cr'
>add/DCA_dd;cc'cr''lf']
<add/DCA_dd'cr'
>add/DCA_dd;cc'cr''lf']
Where: xxxx = AMI, HDB3, or B8ZS.
Where: xxxx = NONE, DATA, or AIS.
Where: xxxx = NONE, DATA, or AIS.
Where:
xxx = TX1, TX2, RX1, or RX2 (service
channel designator).
nnn = -20 to +10 in steps of 1 (service
channel level in dBm).
Where:
xxx = TX1, TX2, TX3, TX4, RX1, RX2, RX3,
or RX4 (backward alarm designator).
nnn = ON or OFF.
Where: xxxxxx = T1, T1ESF, T1IBS, E1CCS,
E1CAS, E1IBS, E131TS, T1S, or T1ESFS.
Where: xxxxxx = T1, T1ESF, T1IBS, E1CCS,
E1CAS, E1IBS, E131TS, T1S, or T1ESFS.
Where: xxx = ON or OFF.
Where:
dd = 1 to N (over the satellite drop channel)
N = (Modulator Data Rate) divided by
(64 kbps).
cc = 1 to 24 (terrestrial channel number for
T1 data formats).
cc = 1 to 31 (terrestrial time slot number for
E1 data formats).
Note: This command is not valid when the drop
data format is specified as E1CAS and the
modulator data rate is set to 1920.0 kbps.
A–11
Revision 1
MN/SDM300L3.IOM